Bedienungsanleitung Kathrein CAP 730 - MobiSet 3 Twin (Seite 10 von 64) (Englisch)

631709

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

10 from 64

5 Installation and connection

5.1 Required tools and equipment

5.2 Unpacking and Preparation

5.3 Selecting the installation location

● Circular cutter, Ø 38 mm

● Flat–bladed screwdriver for M5 screws

● Power drill

● Galvanised round head screws, depending on

the roof structure (Ø: 5 mm, sheet metal screws

D 7981, depending on the roof structure) or

round head screws D 7985 with washers and

nuts

● Twist drill, Ø 2.5 or 5.5 mm

● Roundleand/oremerypaper

● Cleaning agent

● Open-ended or ring spanners 10 and 11 mm

acrossats

● Knife

● Cross-head screwdriver for M3 and M5 screws

● Torque wrench capacity 6 to 11 Nm

● Allen wrench (5 mm)

● Two wooden beams for supporting the turntable

Important

The turntable may not be carried on the sat-

ellite dish, since this can cause it to distort.

Keep the turntable in its cardboard box for

transport on to the vehicle roof.

Retain the original packaging, as if it is necessary

to send the unit for repair transport damage cannot

be ruled out and the manufacturer accepts no liabil-

ity for possible damage.

Loosen the six fastening screws (width A/F:

10 mm). Carefully lift the turntable off the mounting

plate and place it on the two prepared wooden sup-

ports. Make sure that the cables are not crushed

where they emerge from the underside of the turn-

table.

The packaging of the turntable can be opened

along both the long sides. This allows easier access

to the fastening screws.

Essentially, the cable lengths and components that are supplied allow you a free choice of installation loca-

tion on your caravan or motor home. However, you should take note of the following points:

● Beforeinstallation,youshouldndoutwhethertheoperatingmanualforyourvehiclepermitsthetting

ofnon-vehicle-specicpartsorwhatrequirementsneedtobemetinordertodoso.

● For direct satellite reception, there should be no obstructions between the antenna and the satellite.

Therefore, make sure that the antenna is not shadowed by roof extensions such as luggage racks, air

conditioning units, solar panels, etc. The problem of shadowing applies also to the selection of the park-

ing place for your vehicle. For interference–free satellite reception, the antenna needs a projected free

view to the South at an angle of between 0° and 75° (depending on location) to the horizontal.

● When selecting the installation position, take into account the range of movement of the turntable (see

graphics and the “Technical Data” chapter). There may not be any structures on the roof that would

obstruct this range of movement (risk of collision). For safety, keep at least the required area free (for

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kathrein CAP 730 - MobiSet 3 Twin Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kathrein CAP 730 - MobiSet 3 Twin

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info