Bedienungsanleitung Kaysun Aquantia PRO Monobloc - KHP-MO (Seite 54 von 80) (Englisch)

771521

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

During COOL MODE test running, the default target outlet

water temperature is 7°C. The unit will operate until the

water temperature drops to a certain value or the next

command is received.

When the HEAT MODE RUNNING is selected, the follow-

ing page will be displayed:

Go to MENU> FOR SERVICEMAN> 11.TEST RUN.

Press OK. The following page will be displayed:

11 TEST RUN

Active the settings and

active the “TEST RUN”?

OK CONFIRM

NO YES

11 TEST RUN

Test run is on.

Circulation pump is on.

OK CONFIRM

When circulation pump running is turned on, all running

components will stop. 60 minutes later, the 3-way valve

will open, the 2-way valve will close, 60 seconds later

PUMPI will operate. 30s later, if the flow switch checked

normal flow, PUMPI will operate for 3min, after the pump

stops, the 3-way valve will close and the 2-way valve will

open. 60s later the both PUMPI and PUMPO will operate,

2 mins later, the flow switch will check the water flow. If

the flow switch closes for 15s, PUMPI and PUMPO will

operate until the next command is received.

When the COOL MODE RUNNING is selected, the

following page will be displayed:

11 TEST RUN

Test run is on.

Cool mode is on.

Leaving water temperature is

15°C.

OK CONFIRM

When in air purge mode, the 3-way valve will open, the

2-way valve will close. 60s later the pump in the unit

(PUMPI) will operate for 10min during which the flow

switch will not work. After the pump stops, the 3-way valve

will close and the 2-way valve will open. 60s later both the

PUMPI and PUMPO will operate until the next command

is received.

When CIRCULATION PUMP RUNNING is selected, the

following page will be displayed:

11 TEST RUN

Test run is on.

Air purge is on.

OK CONFIRM

If you select AIR PURGE and OK is pressed, the following

page will be displayed :

Before the point check, make sure the tank and

the water system is filled with water, and air is

expelled, or it may cause the pump or backup

heater burn out.

CAUTION

If YES is selected, the following pages will be displayed:

If POINT CHECK is selected, the following pages will be

displayed:

Press ▼ ▲ to scroll to the components you want to check

and press ON/OFF. For example, when 3-way valve is

selected and ON/OFF is pressed, if the 3-way valve is

open/close, then the operation of 3-way valve is normal,

and so are other components.

11 TEST RUN( POINT CHECK)

OFF

ON/OFF ON/OFF

3-WAY VALVE 1

3-WAY VALVE 2

PUMP I

PUMP O

PUMP C

1/2

11 TEST RUN( POINT CHECK)

OFF

ON/OFF ON/OFF

PUMPSOLAR

PUMPDHW

INNER BACKUP HEATER

TANK HEATER

3-WAY VALVE 3

2/2

OK ENTER

11 TEST RUN

11.1 POINT CHECK

11.2 AIR PURGE

11.3 CIRCULATION PUMP RUNNING

11.4 COOL MODE RUNNING

11.5 HEAT MODE RUNNING

OK ENTER

11 TEST RUN

11.6 DHW MODE RUNNING

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kaysun Aquantia PRO Monobloc - KHP-MO Seite 54

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kaysun Aquantia PRO Monobloc - KHP-MO

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info