Bedienungsanleitung Kaysun Aquantia PRO Monobloc - KHP-MO (Seite 55 von 80) (Englisch)

771521

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

During DHW MODE test running, the default target

temperature of the domestic water is 55°C. The TBH(tank

boost heater) will turn on after the compressor runs for

10min. The TBH will turn off 3 minutes later, the heat

pump will operate until the water temperature increase to

a certain value or the next command is received.

During test run, all buttons except OK are invalid. If you

want to turn off the test run, please press OK. For

example ,when the unit is in air purge mode, after you

press OK, the following page will be displayed:

During HEAT MODE test running, the default target outlet

water temperature is 35°C. The IBH (internal backup

heater) will turn on after the compressor runs for 10 min.

After the IBH runs for 3 minutes, the IBH will turn off, the

heat pump will operate until the water temperature

increase to a certain value or the next command is

received.

When the DHW MODE RUNNING is selected, the follow-

ing page will be displayed:

11 TEST RUN

Test run is on.

Heat mode is on.

Leaving water temperature is

15°C.

OK CONFIRM

11 TEST RUN

Test run is on.

DHW mode is on.

Water flow temper. is 45°C

Water tank temper. is 30°C

OK CONFIRM

10.7.12 SPECIAL FUNCTION

When it is in special function modes,the wired controller

can not operate, the page do not return to the homepage,

and the screen showed the page that specical function

runs, the wired controller do not locked.

Press

▼

▲

to scroll the cursor to YES and press OK. The

test run will turn off.

During special function operating other functions

( WEEKLY SCHDULE/TIMER , HOLIDAY AWAY,

HOLIDAY HOME) can’t be used.

NOTE

11 TEST RUN

Do you want to turn off the test run

(AIR PURGE)function?

OK CONFIRM

NO YES When the cursor is on OPERATE PREHEATING FOR

FLOOR, Use

▼

▲

to scroll to YES and press OK. The

following page will be displayed:

Press ▼ ▲ to scroll and press OK to enter.

During first operation of the unit, air may remain in the

water system which can cause malfunctions during

operation. It is necessary to run the air purge function to

release the air (make sure the air purge valve is open).

Go to MENU> FOR SERVICEMAN> 12.SPECIAL FUNC-

TION.

Before floor heating, if a large amount of water remains on

the floor, the floor may be warped or even rupture during

floor heating operation, in order to protect the floor, floor

drying is necessary, during which the temperature of the

floor should be increased gradually.

OK ENTER

12 SPECIAL FUNCTION

12.1 PREHEATING FOR FLOOR

12.2 FLOOR DRYING UP

If PREHEATING FOR FLOOR is selected, after press OK,

the following page will be displayed:

12.1 PREHEATING FOR FLOOR

30°C

72 HOURS

ADJUST

T1S

t_fristFH

ENTER EXIT

12.1 PREHEATING FOR FLOOR

Preheat for floor is

running for 25 minutes.

Water flow temperature is 20°C.

OK CONFIRM

12 SPECIAL FUNCTION

Active the settings and active the

“SPECIAL FUNCTION”?

OK CONFIRM

NO YES

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kaysun Aquantia PRO Monobloc - KHP-MO Seite 55

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kaysun Aquantia PRO Monobloc - KHP-MO

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info