Bedienungsanleitung Kaysun Aquantia PRO Monobloc - KHP-MO (Seite 65 von 80) (Englisch)

771521

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

When a safety device is activated, an error code will be displayed on the user interface.

A list of all errors and corrective actions can be found in the table below.

Reset the safety by turning the unit OFF and back ON.

In case this procedure for resetting the safety is not successful, contact your local dealer.

13.4 Error codes

The power consumption parameter is preparatory. some parameter is not be activated in the system, the parameter will

show "--"

The heat pump capacity is for reference only, not used to judge the ability of the unit. The accuracy of sensor is ±1

℃.

The flow rates parameters are calculated according to the pump running parameters,the deviation is different at different flow

rates,the maximum of deviation is 25%.

NOTE

OPERATION PARAMETER

#01

IDU TARGET FREQUENCY 46Hz

ADDRESS

FREQUENCY LIMITED TYPE 5

FAN SPEED 600R/MIN

SUPPLY VOLTAGE 230V

DC GENERATRIX VOLTAGE 420V

DC GENERATRIX CURRENT 18A

7/9

OPERATION PARAMETER

#01

TW_I PLATE W-INLET TEMP. 30°C

ADDRESS

T2 PLATE F-OUT TEMP. 35°C

TW_O PLATE W-OUTLET TEMP. 35°C

T2B PLATE F-IN TEMP. 35°C

Th COMP. SUCTION TEMP. 5°C

Th COMP. DISCHARGE TEMP. 75°C

8/9

OPERATION PARAMETER

#01

T4 OUTDOOR AIR TEMP. 5°C

ADDRESS

TF MODULE TEMP. 55°C

T3 OUTDOOR EXCHARGE TEMP. 5°C

P1 COMP. PRESSURE 2300kPa

ODU SOFTWARE 01-09-2018V01

HMI SOFTWARE 01-09-2018V01

9/9

ERROR

CODE

MALFUNCTION

OR PROTECTION

FAILURE CAUSE

AND CORRECTIVE ACTION

Water flow fault (E8

displayed 3 times)

1.The wire circuit is short connected or open. Reconnect the wire

correctly.

2.Water flow rate is too low.

3. Water flow switch is failed, switch is open or close continuously,

change the water flow switch.

Phase loss or neutral wire and

live wire are connected

reversely

1.Check the power supply cables should be connected stable, to avoid

phase loss.

2.Check the power supply cables sequence, change any two cables

sequence of the three power supply cables.

Communication fault between

controller and main control

board of hydraulic module

’

1.The wire doesn’t connect between wired controller and unit. connect

the wire.

2.Communication wire sequence is not right. Reconnect the wire in

the right sequence.

3. Whether there is a high magnetic field or high power interfere, such

as lifts, large power transformers, etc..

4. To add a barrier to protect the unit or to move the unit to the other

place.

Final outlet water temp. sensor

(T1) fault.

1. Check the resistance of the sensor

2. The T1 sensor connector is loosen. Reconnect it.

3.The T1 sensor connector is wet or there is water in. remove

the water, make the connector dry. Add waterproof adhesive.

4.The T1 sensor failure, change a new sensor.

Water tank temp. sensor

(T5) fault.

1. Check the resistance of the sensor

2.The T5 sensor connector is loosen. Reconnect it.

3.The T5 sensor connector is wet or there is water in. remove

the water, make the connector dry. Add waterproof adhesive

4.The T5 sensor failure, change a new sensor

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kaysun Aquantia PRO Monobloc - KHP-MO Seite 65

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kaysun Aquantia PRO Monobloc - KHP-MO

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info