Bedienungsanleitung Kaysun Aquantia PRO Monobloc - KHP-MO (Seite 66 von 80) (Englisch)

771521

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

ERROR

CODE

MALFUNCTION

OR PROTECTION

FAILURE CAUSE

AND CORRECTIVE ACTION

The condenser outlet

refrigerant temperature sensor

(T3) fault.

1. Check the resistance of the sensor

2. The T3 sensor connector is loosen. Reconnect it.

3.The T3 sensor connector is wet or there is water in. remove

the water, make the connector dry. Add waterproof adhesive

4. The T3 sensor failure, change a new sensor.

The ambient temperature

sensor (T4) fault.

1. Check the resistance of the sensor

2. The T4 sensor connector is loosen. Reconnect it.

3.The T4 sensor connector is wet or there is water in. remove

the water, make the connector dry. Add waterproof adhesive

4. The T4 sensor failure, change a new sensor.

The balance tank up temp.

sensor (Tbt1) fault.

1.Check the resistance of the sensor.

2.The Tbt1 sensor connector is loosen,reconnect it.

3.The Tbt1 sensor connector is wet or there is water in,remove the

water ,make the connector dry.Add waterproof adhesive.

4.The Tbt1 sensor failure,change a new sensor.

Water flow fault.

Check that all shut off valves of the water circuit are completely open.

1.Check if the water filter needs cleaning.

2.Refer to "9.4 Charging water"

3.Make sure there is no air in the system(purge air).

4. Check on the manometer that there is sufficient water pressure. The

water pressure must be >1 bar.

5.Check that the pump speed setting is on the highest speed.

6.Make sure that the expansion vessel is not broken.

7. Check that the resistance in the water circuit is not too high for the

pump (refer to "Setting the pump speed" ).

8. If this error occurs at defrost operation (during space heating or

domestic water heating), make sure that the backup heater power

supply is wired correctly and that fuses are not blown.

9.Check that the pump fuse and PCB fuse are not blown.

Compressor suction temp.

sensor (Th) fault.

1.Check the resistance of the sensor.

2. The Th sensor connector is loosen. Reconnect it.

3.The Th sensor connector is wet or there is water in. remove

the water, make the connector dry. Add waterproof adhesive

4. The Th sensor failure, change a new sensor.

Compressor discharge temp.

sensor (Tp) fault.

1.Check the resistance of the sensor.

2. The Tp sensor connector is loosen. Reconnect it.

3.The Tp sensor connector is wet or there is water in. remove

the water, make the connector dry. Add waterproof adhesive

4. The Tp sensor failure, change a new sensor.

Solar panel temp.sensor

(Tsolar) fault.

1.Check the resistance of the sensor.

2.The Tsolar sensor connector is loosen,reconnect it.

3.The Tsolar sensor connector is wet or there is water in,remove the

water ,make the connector dry.Add waterproof adhesive.

4.The Tsolar sensor failure,change a new sensor.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kaysun Aquantia PRO Monobloc - KHP-MO Seite 66

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kaysun Aquantia PRO Monobloc - KHP-MO

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info