Bedienungsanleitung Kaysun KAY-CF 71 DR8 (Seite 19 von 36) (Englisch)

771401

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

15 cm (5,9 in) or more

2,3 m (90,55 in) or more

12 cm (4,75

in) or more

12 cm (4,75

in) or more

Ondoor

Muro

Outdoor

 Page 19 

7. Indoor Unit Installation

Installation Instructions - Indoor Unit

PRIOR TO INSTALLATION

Before installing the indoor unit, refer to the label on the

product box to make sure that the model number of the

indoor unit matches the model number of the outdoor unit.

Step 1: Select installation location

Before installing the indoor unit, you must choose an

appropriate location. The following are standards that will

help you choose an appropriate location for the unit.

Proper installation locations meet the following

standards:

5Good air circulation.

5Convenient drainage.

5Noise from the unit will not disturb other people.

5Firm and solid - the location will not vibrate.

5Strong enough to support the weight of the unit.

5A location at least one meter from all other electrical

devices (e.g., TV, radio, computer).

DO NOT install unit in the following locations:

Near any source of heat, steam, or combustible gas.

Near ammable items such as curtains or clothing.

Near any obstacle that might block air circulation.

Near the doorway.

In a location subject to direct sunlight.

NOTE ABOUT WALL HOLE

If there is no xed refrigerant piping:

While choosing a location, be aware that you should

leave ample room for a wall hole (see Drill wall hole for

connective piping step) for the signal cable and refrigerant

piping that connect the infoor and outdoor units. The

default position for all piping is the right side of the

indoor unit (while facing the unit). However, the unit can

accomodate piping to both the left and right.

Refer to the following diagram to ensure proper

distance from walls and ceiling:

Step 2: Attach mounting plate to wall

The mounting plate is the device on which you will

mount the indoor unit.

• Take out the mounting plate at the back of the indoor

unit.

• Secure the mounting plate to the wall with the screws

provided. Make sure that mounting plate is at against

the wall.

NOTE FOR CONCRETE OR BRICK WALLS

If the wall is made of brick, concrete, or similar material,

drill 5mm-diameter (0.2in-diameter) holes in the wall

and insert the sleeve anchors provided. Then secure

the mounting plate to the wall by tightening the screws

directly into the clip anchors.

Step 3: Drill wall hole for connective piping

1. Determine the location of the wall hole based on the position

of the mounting plate. Refer to Mounting Plate Dimensions.

2. Using a 65mm (2.5in) or 90mm (3.54in) (depending on

models) core drill, drill a holte in the wall. Make sure that

the hole is drilled at a slight downward angle, so thta the

outdoor end of the hole is lower than the indoor end by

about 5mm to 7mm (0.2-0.275in). This will ensure proper

water drainage.

3. Place the protective wall cuff in the hole. This protects the

edges of the hole and will help seal it when you nish the

installation process.

CAUTION

When drilling the wall hole, make sure to avoid wires,

plumbing, and other sensitive components.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kaysun KAY-CF 71 DR8 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kaysun KAY-CF 71 DR8

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info