Bedienungsanleitung Keiser M3 - Total Body Trainer (Seite 14 von 24) (Englisch)

738042

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

M3i | M3 TOTAL BODY TRAINER

Apply Rust Inhibitor to the Left Bottom Bracket Bearing and to both Link Bearings

(recommended annually after initial assembly, see Figure 5).

When all assembly requirements have been met, and you have read and understood

the Important Safety Instructions, test ride the TBT. Fine-tune and adjust the Seat

height/depth and Base Stabilizer as needed. It is recommended that the TBT be

pedaled in the forward direction.

Proper Operation Check:

• All Screws are tightened or torqued properly (refer to “How to Assemble the Total

Body Trainer” section, beginning on page 10, Steps 2 — 12).

• The Computer Display powers ON (pedal one full revolution) and the Resistance

Lever cycles GEAR 1—24 (GEAR 88 = Emergency Brake).

• TBT is properly stabilized, level to the oor (refer to “Base Stabilizer” section below).

• The Seat height/depth are properly set (refer to “Seat Height Adjustment Knob”

and “Seat Depth Adjustment L-Handle” sections, page 15).

Figure 5. Rust Inhibitor

Application

Figure 6. Transporting the TBT

PROPER OPERATION CHECK

TRANSPORT

BASE STABILIZER

To position the TBT at the desired location refer to Figure 6 and

follow the instructions below:

Be sure there is a minimum of 24 inches (610 mm) free space

for the TBT on all sides before placement.

1. Grasp the Handles with both hands.

2. Tilt the TBT toward you until the Transport Wheels contact

the oor.

3. Roll the TBT to the desired location; tilt it slowly away from

you to set down.

The TBT must be placed on a at, level surface. If the sub-oor is not

level, the Base Stabilizer allows for stabilization.

To stabilize the TBT, refer to Figure 7 and follow the instructions

below:

1. Hold the Seat steady, then with your foot, swipe the Base

Stabilizer counter-clockwise to drive it back into the base. This

will un-stabilize the TBT.

2. Slightly push across the Seat, until the Base Feet at all three

corners contact the oor, then hold.

3. With the three Base Feet making contact with the oor, swipe

the Base Stabilizer clockwise with your foot until the Base

Stabilizer makes contact with the oor. This will stabilize the

TBT.

Test for stability.

The TBT should sit at without rocking. Adjust and

ne-tune the Base Stabilizer as needed.

NOTE: The TBT should not be used until it is stabilized. If the TBT is

moved to a different location, adjust the Base Stabilizer as needed

to stabilize the TBT.

WARNING: To reduce the risk of serious injury, read all important precautions and instructions in this manual

and all warnings on the TBT before operation. Failure to perform the Proper Operation Check prior to operation of

the TBT will void your warranty and could result in serious injury.

Figure 7. Base Stabilizer Adjustment



Floor

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Keiser M3 - Total Body Trainer Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info