Bedienungsanleitung Kenwood DRV-830 (Seite 17 von 25) (Englisch)

683035

Zoom out

Zoom in

Vorherige Seite

1/25

Nächste Seite

Configuring the Settings

Playback

Continuous REC (Slot 1) Select the folder and play the desired ﬁle. (➜ P. 26)

It is also possible to protect or delete the ﬁle during ﬁle playback. (➜ P. 28)

Continuous REC (Slot 2)

Manual REC

Event REC

Parking REC

Still images

Parking recording settings

To use the parking recording function, the power must be connected with the CA-DR100 (optional

accessory). (➜ P. 14)

Recording time OFF (parking recording not performed)/10 sec*/20 sec /30 sec

Set the time for recording after an impact is detected.

Overwrite ON*/OFF

Set whether or not to overwrite old ﬁles after the maximum number of recording

ﬁles has been reached.

Detecting sensitivity 1 (Low Sensitivity)/2/3*/4/5 (High Sensitivity)

Set the sensitivity for detection of impacts to the parked vehicle.

Exit time after ACC OFF OFF*/30 sec/1 min/3 min

Set the time for which parking recording will be disabled after the engine key

is turned oﬀ.

Entry time before ACC ON OFF*/30 sec/1 min/3 min

Set the time for which parking recording will be disabled before the engine key

is turned on.

* Factory default settings

Recording settings

Audio recording ON*/OFF

Set whether or not to record the sound from the microphone when recording.

Continuous recording ﬁle

length

1 min*/3 min/5 min

Set the recording time for continuous recording. The recordings are split according

to the recording time set here.

For low frame rate recordings, the ﬁle length is 10 minutes, regardless of the

value set here.

Manual recording time 15 sec*/30 sec/1 min

Set the time for recording after manual recording is started. The recording time

before the [REC] button is set is ﬁxed to 10 seconds.

Event recording time 15 sec.*/30 sec./1 min.

Set the time for recording after an impact is detected. The recording time before

an impact to the vehicle is detected is ﬁxed to 10 seconds.

Overwrite (manual) ON/OFF*

Set whether or not to overwrite old ﬁles after the maximum number of recording

ﬁles has been reached.

Overwrite (event) ON/OFF*

Set whether or not to overwrite old ﬁles after the maximum number of recording

ﬁles has been reached.

Resolution 2560×1440 (HDR)/2304×1296 (HDR)

/1920×1080 (HDR)*/1280×720 (HDR)

Sets the resolution for recording.

Recording mode Normal*/Low frame rate

Select a recording mode. Selecting low frame rate recording increases the recording

time to more than usual.

Low frame rate 9 fps*/3 fps

Set the image update frequency during low frame rate recording. The smaller the

value, the longer the recording time.

Detecting sensitivity (event) 1 (Low Sensitivity) /2/3*/4/5 (High Sensitivity)

Set the sensitivity for detecting impacts to the vehicle.

Automatic still image capture Capture interval

1 min./5 min.*/15 min./30 min.

Set the interval for capturing images with the automatic still image capture function.

Number of captured images

10/30*/50

Set the number of images to be captured with the automatic still image capture

function.

Information stamps ON*/OFF

Set whether or not to record subtitles (date and time, position information, etc.).

* Factory default settings

3332

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood DRV-830 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood DRV-830

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info