Bedienungsanleitung Kenwood DRV-830 (Seite 18 von 25) (Englisch)

683035

Zoom out

Zoom in

Vorherige Seite

1/25

Nächste Seite

Configuring the Settings

Driving support settings

Forward collision warning ON/OFF*

This function detects the distance between you and the vehicle in front, and

sounds a warning if the distance is not safe in order to prevent a collision with

the vehicle in front. This functions at speeds of approximately 30 km/h and higher.

Lane departure warning ON/OFF*

This function detects the lane in which you are driving and sounds a warning if you

veer out of that lane. This functions at speeds of approximately 60 km/h and higher.

Departure delay warning ON/OFF*

This function sounds a warning if, while you are stopped, the vehicle in front of

you has taken oﬀ and your departure is too slow. With this function, a warning is

also sounded if you are backing up.

Detection range Adjust the horizon, position of the front tip of the engine hood, etc., before using

the driving support functions. (➜ P. 17)

Mounting height 1.2 m*/1.35 m/2 m

Set the height from the road surface to the position at which the camera is

mounted. (➜ P. 17)

System settings

Date/time Automatic*/Manual

Set whether to record the date and time automatically or manually. (➜ P. 36)

You must set the “Time Zone”

Daylight saving time OFF*/+1 hr./+30 min Set daylight saving time.

Notiﬁcation volume The volume of the notiﬁcation sound can be set in 6 steps (mute to maximum).

The notiﬁcation sound is the sound issued as guidance during event recording,

when operating buttons, etc.

Playback volume

Set the volume of the sound when playing recorded ﬁles in 6 steps (mute to

maximum).

Monitor Time settings 10 sec.*/1 min./3 min.

Set the time after which the monitor screen switches to the power-saving mode

during recording.

Operation settings

Always on*/OFF/Dim

Set the monitor screen's power-saving operation during recording. When the

MENU/OK button is pressed, the power-saving operation is temporarily canceled.

Mounting support tool Level

Use this to check whether the camera is level.

Satellite reception level

This displays the positioning satellite reception strength screen.

Select units km/h/mph*

Switch to kilometer or mile display.

Factory reset Restores the settings to the values set upon purchase.

When executed, the power turns oﬀ then back on and the setup screen appears.

Follow the instructions on the screen to conﬁgure the settings.

Setup Conﬁgure the settings related to installation of the camera in a speciﬁc order.

Update system Update the camera's ﬁrmware.

System version Display the camera's ﬁrmware version.

About updating the system

This function updates the camera's system ﬁrmware. For information and instructions on

updating, see the Kenwood website. http://www.kenwood.com/cs/ce/

SD card menu

SD card information (Slot 1) Display the information screen for the SD card in slot 1.

SD card information (Slot 2) Display the information screen for the SD card in slot 2.

Format SD card (Slot 1) Formats the SD card in slot 1, deleting all the ﬁles on the card.

Format SD card (Slot 2) Formats the SD card in slot 2, deleting all the ﬁles on the card.

* Factory default settings

3534

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood DRV-830 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood DRV-830

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info