Bedienungsanleitung Kenwood kac 526 (Seite 54 von 76) (Englisch)

165284

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

— 54 —

English

"CODE" appears in the display, you can start inputting the code.

Press the Preset button and input the security code again.

Hold down the DISP button again for three seconds or more.

"APPROVED" will appear in the display, with the code security

function turning on. From this point on, if the unit is

disconnected from the battery, the security code must be

entered the first time that the unit's power is turned on.

"ENTER" and "CODE" will appear in the display, asking you to

input the code.

If you input an incorrect security code, the code setting mode

will be cancelled automatically. Follow the steps from 3 to 7

above again.

If you press the RESET button or remove the battery:

The first time you turn the unit on again, "CODE" will appear in

the display, asking you to input the security code.

Repeat steps 6 and 7 above, and input the security code.

You can start operating the unit again when "APPROVED"

appears in the display.

If you enter the wrong code, "Waiting" is displayed and you

cannot make further input of the code for a fixed interval (see

table below), which grows longer each time you enter the wrong

code.

When "CODE" is displayed, you can make input again.

The number of wrong inputs is displayed.

Number of wrong

inputs

Interval until next input

is allowed

2 5 minutes

3 1 hour

4 24 hours

NOTE

After a security code has been registered, power cannot be

restored if the battery is disconnected from the unit unless the

code is first input.

All the steps in this procedure (1 through 7) must be completed

before the code security function can be turned on. However,

once the procedure is finished, it need not be repeated.

Once the code security function has been activated, "Security"

disappears from the MENU system. Note that it will no longer be

possible to cancel this function afterwards.

Press the SRC button repeatedly to select the standby mode.

"ALL OFF" is displayed when the standby mode is selected.

Hold down the MENU button for one second or more.

"MENU" is displayed first and then "Security" is displayed.

Hold down either the 4 or ¢ button for one second or

more.

"ENTER" will appear in the display for one second, indicating

the code setting mode has been entered. When "CODE"

appears in the display, you can start inputting the code.

Press the preset button and enter your security code.

Use the security code shown on your Car Audio Passport.

Example: Enter "3510" as your code, pressing the buttons as

follows:

Hold down the DISP button for three seconds or more.

The security code will be set.

"RE-ENTER" will appear in the display for one second, asking

you to enter the code once again for confirmation. When

Step Button to press

# Times

pressed

Display

#1 4

6#2

#3 2

#4 1

“3”

“5”

“1”

“0”

NOTE

Code Security Function <In Standby mode>

Menu settings

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood kac 526 Seite 54

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info