Bedienungsanleitung Kenwood TM-D710GA (Seite 27 von 77) (Englisch)

606707

Zoom out

Zoom in

Vorherige Seite

1/77

Nächste Seite

EchoLink-2

■ Selecting a Transmit Speed

Some repeaters may not respond correctly if a code is

transmitted at fast speed. If this happens, change the

EchoLink transmission speed from FAST (default) to SLOW.

1 Enter Menu mode and access Menu 205.

2 Set the speed to FAST or SLOW.

SETTING UP EchoLink Sysop MODE

Connect the TM-D710G to a personal computer to use the

system as a node station for EchoLink relaying.

When connecting to a personal computer and using the

EchoLink Sysop mode, the hard ﬂ ow control operation RTS and

CTS computer terminals operate the same as and are changed

with the SQC (squelch control signal output to the computer)

and PKS (transmit control signal input from the computer) data

terminals.

The current band becomes the same as the data band which is

selected in menu No. 918 regardless of the transmission band

and operation band.

Use the PG-5H (interface cable kit) when connecting to a

personal computer.

Data communications cable

Serial communications cable

To PC audio terminal

Pink: To microphone input terminal

Green: To line out terminal

To PC 9-pin D-SUB terminal

1 Turn the transceiver power OFF.

2 Press [PF2] + Power ON to turn EchoLink Sysop Mode ON.

• The icon appears on the display when EchoLink Sysop mode

is ON.

• When the audio signal is output to the PC side, the

icon

blinks.

• To turn EchoLink Sysop Mode OFF, press [PF2] + Power ON

again.

EchoLink Sysop Mode ON EchoLink Sysop Mode OFF

terminal

TxD



RxD TxD



RxD



TxD RxD



TxD

SQC



CTS RTS



CTS

PKS



RTS CTS



RTS

GND



GND GND



GND

Note:

◆ When using EchoLink Sysop mode, perform the following settings (1) ~ (4).

(1) Set the SQC output setting (Menu No. 921) to “SQL”.

(2) When unnecessary noise signals, etc., are sent from the link station

to the internet while CTCSS and DCS are active, use can verify the

usage condition of the operating frequency by setting “EchoLink RX

Monitor” ([Edit] > [Menu] > [Transmit/Receive]) via the MCP-6A to

“Busy Only”.

Because of this, when EchoLink Sysop mode is ON, all received

signals on the DATA band are output from the speaker irregardless of a

matching CTCSS or DCS signal.

(Voice signals are output from the DATA terminal only when the

CTCSS or DCS signals match.)

(3) To avoid having the EchoLink software detecting a busy state even

when the transceiver power is turned OFF, set the “SQC Output Logic”

([Edit] > [Data Terminal]) via the MCP-6A to “High”.

(When performing this setting, ensure that the EchoLink’s software

“Invert Sense” setting in the RX Ctrl tab of the Sysop Setup window is

not checked.)

(4) When the audio level adjustment range on your personal computer is

insufﬁ cient, adjust the AF output level “PR1 Pin Output Level” ([Edit] >

[Data Terminal]) and AF input sensitivity “PKD Pin Input Level” ([Edit]

> [Data Terminal]) of the transceiver via the MCP-6A. Adjustments can

be made in steps of 6dB.

◆ The settings in numbers 2 ~ 4 (above) can be performed only using a MCP-

6A.

◆ When EchoLink Sysop mode is ON, it cannot communicate with the MCP-

6A. When using the MCP-6A, be sure to turn EchoLink Sysop mode OFF.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood TM-D710GA Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood TM-D710GA

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info