Bedienungsanleitung Kenwood TM-D710GA (Seite 47 von 77) (Englisch)

606707

Zoom out

Zoom in

Vorherige Seite

1/77

Nächste Seite

ADJUSTING THE INTERNAL CLOCK

When the internal GPS function is turned ON, the year, month,

day, and time are automatically set from the GPS satellite

information. If the GPS information cannot be received, you can

manually enter the date and time.

Note: The battery for the clock backup is built into the unit. When the power

source is connected, the battery begins to charge. It takes approximately 12

hours to become fully charged.

■ Setting Date

1 Enter Menu mode and access Menu 925.

• The ﬁ rst 2 digits blink.

2 Rotate the Tuning control to enter the current month (TM-

D710GA) or day, then press the Tuning control.

• The next 2 digits blink.

3 Rotate the Tuning control to enter the current day (TM-

D710GA) or month, then press the Tuning control.

• The last 2 digits blink.

4 Rotate the Tuning control to enter the current year, then

press the Tuning control.

5 Press [ESC] to exit Menu mode.

Note:

◆ When used at room temperature (25°C), the error of the internal clock in a

month is within one minute.

◆ The internal clock is effective until December 31, 2099.

■ Setting Time

1 Enter Menu mode and access Menu 926.

• The ﬁ rst 2 digits blink.

2 Rotate the Tuning control to enter the current hour, then

press the Tuning control.

• To set 1 o'clock PM for example, select 13.

• The next 2 digits blink.

3 Rotate the Tuning control to enter the current minute,

then press the Tuning control.

4 Press [ESC] to exit Menu mode.

■ Setting UTC Offset

1 Enter Menu mode and access Menu 927.

2 Rotate the Tuning control to select the appropriate UTC

offset, then press the Tuning control.

• The selectable range is from +14:00 to –14:00 in steps of 15

minutes.

3 Press [ESC] to exit Menu mode.

APRS-2

CONNECTING WITH A EXTERNAL GPS RECEIVER OR

WEATHER STATION

The GPS jack on this transceiver accepts a 2.5 mm (1/10")

3-conductor plug. If necessary, use the supplied cable to modify

the cable end of external GPS receiver or Weather Station.

• Use an external GPS receiver which conforms to the NMEA-0183

format and is compatible with RS-232C signal polarity output at the

below mentioned levels.

[Low level: –15.0V ~ +0.5 V / High level: +3.0V ~ +15.0V]

You cannot use GPS receivers with USB-type connections.

• Set Menu No. 602 (GPS PORT-INPUT) to “GPS” (

external GPS

receiver), “WEATHER (Davis)” (Weather Station), or “WEATHER

(PeetBros.)” (Weather Station), depending on the equipment

connected to the GPS terminal.

When an

external GPS receiver is selected, the “GPS” indicator

appears. When a Weather Station is selected, the “WXI” indicator

appears.

External GPS receiver

To GPS jack

Shield

(to GND on GPS/ WX)

Red

(to DATA OUT on GPS/ WX)

White

(to DATA IN on GPS/ WX)

Weather Station

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood TM-D710GA Seite 47

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood TM-D710GA

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info