Bedienungsanleitung Kenwood TM-D710GA (Seite 59 von 77) (Englisch)

606707

Zoom out

Zoom in

Vorherige Seite

1/77

Nächste Seite

APRS-14

■ TX Interval Time <TX INTERVAL>

You can change the interval for automatically transmitting

APRS packets. Access <TX INTERVAL > and select 0.2, 0.5,

1, 2, 3, 5, 10, 20, 30 or 60 minutes. The default is 3 minutes.

Note:

◆ With “AUTO” in < METHOD > and Beacon ON, pressing the Tuning

control to complete the setting causes the APRS packet to be immediately

transmitted. After that, APRS packets are transmitted at intervals of the

selected period.

◆ While signals are present, an APRS packet is not transmitted after the

interval. after signals drop, transmitting is executed.

■ Decay Algorithm <DECAY ALGORITHM>

This function continuously extends the packet transmission

interval in the case that there is no change of position

information.

• When the position data does not change, the data is transmitted

based on a Decay Algorithm (1 minute, 2 minutes, 4 minutes, 8

minutes, 16 minutes, 32 minutes, 32 minutes, 32 minutes, etc.)

• When My station position data changes, the data is transmitted

using an interval time based on the set Initial Interval.

• When the set time elapses and transmission is performed but a

busy signal is present, the transceiver does not transmit. When

there is no longer a busy signal, the transceiver attempts to

transmit.

Note:

◆ While transmitting by pressing the [PTT] switch, beacon transmission is

reserved.

◆ If My callsign is not set, the APRS packet will not be transmitted.

◆ Independent of this interval, the transmission of the message is in 1 minute

intervals.

■ Proportional Pathing <PROPORTIONAL PATHING>

This function automatically changes the transmit packet path with

the elapsed time.

Operation example for when PROPORTIONAL PATHING = ON

Transmission interval is 2 minutes. (When the <DECAY

ALGORITHM> = ON, the decay transmission interval takes

precedence.)

The packet path changes with each transmission as shown

below (when the packet path is set as WIDE1-1, WIDE2-1).

2 minutes : DIRECT

4 minutes : WIDE1-1 (1 Hop)

6 minutes : DIRECT

8 minutes : WIDE1-1, WIDE2-1 (2 Hops)

10 minutes : DIRECT

12 minutes : WIDE1-1 (1 Hop)

14 minutes : DIRECT

16 minutes : WIDE1-1, WIDE2-1 (2 Hops)

This is repeated.

When jointly using a Decay Algorithm, if the speed is 1 knots or

slower, a Decay Algorithm pattern is used for transmitting, but if the

speed is 3 knots or faster, it changes to Proportional Pathing.

PROGRAMMING A PACKET PATH

Enter Menu mode and access Menu 612.

Select the packet path type from [New-N PARADIGM], [RELAY

PARADIGM], [STATE/SECTION/REGION], or [OTHERS].

When you press [USE], the “

” indicator appears on the left side

of the packet path type, showing the current used information.

[New-N PARADIGM]:

This digipeat type has been used mainly in North America, but is

now used worldwide.

1 Set the TYPE to [New-N PARADIGM], then press [USE].

2 Set WIDE 1-1 to [OFF] or [ON].

• Set WIDE 1-1 to [ON] to use the digipeater of the RELAY type

(Fill-in type) with the New-N PARADIGM.

• When set to [ON], 1 packet path in addition to WIDE 1-1 can be

used, as per the TOTAL HOPS setting.

3 Select the relay step number for the TOTAL HOPS setting.

• You can conﬁ rm the setting contents in PATH IS VIA.

[RELAY PARADIGM]:

This is one of the digipeat types used in Europe.

1 Set the TYPE to [RELAY PARADIGM], then press [USE].

2 Set RELAY to [OFF] or [ON].

• Set RELAY to [ON] to use the digipeater of the RELAY type (Fill-

in type) with the RELAY PARADIGM.

• When set to [ON], 1 packet path in addition to RELAY can be

used, as per the TOTAL HOPS setting.

3 Select the relay step number for the TOTAL HOPS setting.

• You can conﬁ rm the setting contents in PATH IS VIA.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood TM-D710GA Seite 59

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood TM-D710GA

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info