Bedienungsanleitung Kenwood TM-D710GE (Seite 11 von 77) (Englisch)

606708

Zoom out

Zoom in

Vorherige Seite

1/77

Nächste Seite

MEMORY CH-1

MEMORY CHANNELS

In Memory channels, you can store frequencies and related data that you often use. Then you need not reprogram the data every time.

You can quickly recall a programmed channel by simple operation. A total of 1000 Memory channels are available for bands A and B.

SIMPLEX & REPEATER OR ODD-SPLIT MEMORY

CHANNEL?

You can use each memory channel as a simplex & repeater

channel or as an odd-split channel. Store only one frequency to

use as a simplex & repeater channel or two separate frequencies

to use as an odd-split channel. Select either application for each

channel depending on the operations you have in mind.

Simplex & repeater channels allow:

• Simplex frequency operation

• Repeater operation with a standard offset (if an offset

direction is stored)

Odd-split channels allow:

• Repeater operation with a non-standard offset

The data listed below can be stored in each Memory channel:

Parameter

Simplex &

Repeater

Odd-split

Receive frequency

Ye s

Transmit frequency Yes

Receive frequency step

size

Ye s

Transmit frequency step

size

Ye s

Offset direction Yes No

Tone ON/OFF Yes Yes

Tone frequency Yes Yes

CTCSS ON/OFF Yes Yes

CTCSS frequency Yes Yes

DCS ON/OFF Yes Yes

DCS code Yes Yes

Reverse ON/OFF Yes No

Memory channel lockout Yes Yes

Memory channel name Yes Yes

Modulation/

Demodulation mode

Ye s Ye s

STORING SIMPLEX AND STANDARD REPEATER

FREQUENCIES

1 Press [VFO] to enter VFO mode.

2 Rotate the Tuning control to select your desired frequency.

• Additionally, you can press the microphone [UP]/[DWN] keys to

select a frequency.

3 Set up any additional data desired for the frequency.

• Offset direction, Tone ON/OFF, Tone frequency, CTCSS ON/OFF,

CTCSS frequency, DCS ON/OFF, DCS code, etc.

4 Press [F].

• A memory channel number appears.

5 Rotate the Tuning control to select your desired channel

number.

• When the selected channel number does not have stored data,

the “ ” icon appears. When the channel does have stored data,

the “ ” icon appears.

• Additionally, you can press the microphone [UP]/[DWN] keys to

select a channel.

6 Press [M.IN] to store the data in the selected Memory

channel.

Note: If you store the data in a Memory channel that already has data stored in

it, the old data will be cleared and the new data will be stored.

■ Call Channel Memory (Simplex)

The Call channel can be used to store any frequency and

related data that you will recall often. You may want to

dedicate the Call channel as an emergency channel within

your group.

To store a simplex frequency and related data as the Call

channel instead of in a Memory channel, after step 4 (above),

press [C.IN].

Note: Storing new data in the Call channel will clear the old data. (The Call

channel itself cannot be cleared, but data can be replaced with new data.)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood TM-D710GE Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood TM-D710GE

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info