Bedienungsanleitung Kenwood TS-2000E (Seite 88 von 150) (Englisch)

45743

Zoom out

Zoom in

Vorherige Seite

1/150

Nächste Seite

15 OPERATOR CONVENIENCES

QUICK DATA TRANSFER

This transceiver has the capability to quickly and

conveniently transfer the receive frequency and mode

to another compatible transceiver. Compatible

transceivers include:

• TS-2000(X) • TS-570S/ 570D

• TS-850S • TS-870S

• TS-690S • TS-950SDX

• TS-450S

Data Transfer could be useful while contesting. A

spotting station that is searching for new contest

multipliers can quickly transfer a frequency over to

the running (main) station.

SETTING UP

■ Equipment Needed

In addition to a compatible transceiver, the following

equipment is required:

Transfer to TS-2000(X), TS-570, or TS-870S:

• One cross-wired cable. This cable must have a

9-pin RS-232C female connector at both ends.

Transfer to a transceiver other than TS-2000(X),

TS-570, and TS-870S:

• KENWOOD IF-232C interface unit.

• One cross-wired cable. This cable must have a

9-pin RS-232C female connector at one end and a

25-pin RS-232C female connector at the other

end.

• One straight cable. This cable must have a

6-pin DIN male connector at both ends.

■ Connections

For diagrams on how to connect the two transceivers,

see “CONNECTING PERIPHERAL EQUIPMENT”

{page 93}.

Note: If you are using a DSP-100 unit with the transceiver, turn on

the transceiver first, then turn on the DSP-100.

USING QUICK TRANSFER

When connecting with another TS-2000(X), TS-570,

or TS-870S, use the same COM connector baud rate

on each transceiver. If transferring to or from other

KENWOOD transceivers, select 4800 bps and 2 stop

bits. On the TS-2000(X), set the parameter in Menu

No. 56 to 4800 bps.

Note: While transferring data, other functions may work slower.

■ Transferring Data

The TS-2000(X) transceiver works as the Master,

sending data to the Slave transceiver.

1 Switch ON the Transfer function of each

transceiver.

• On the TS-2000(X), access Menu No. 52 and

select ON. For the compatible transceiver,

refer to the instruction manual that came with

the transceiver.

2 On the Master, while in VFO mode, select an

operating frequency and mode.

3 On the Master, press QUICK MEMO [M.IN].

• When using another TS-2000(X) as the Slave,

“PC” appears on the Slave.

• The displayed data is stored in Quick memory

channel 0 on the Master and transferred to the

Slave.

Note: If the Master has RIT switched ON, the offset frequency is

added to the receive frequency to be transferred.

■ Receiving Data

The TS-2000(X) transceiver works as the Slave,

receiving data from the Master transceiver. The

Slave can receive data using either Quick memory

channel 0 or the VFO.

1 Switch ON the Transfer function of each

transceiver.

• On the TS-2000(X), access Menu No. 52 and

select ON. For the compatible transceiver,

refer to the instruction manual that came with

the transceiver.

2 On the Slave, access Menu No. 53 and select

either OFF (QUICK MEMO channel 0) or ON

(the VFO).

• The default is OFF (QUICK MEMO).

3 On the Master, perform the appropriate operation

to send data.

• For the correct method, refer to the instruction

manual that came with the transceiver.

Note:

◆

If you always use the TS-2000(X) for receiving only, activate the

TX Inhibit function, accessing Menu No. 54 to avoid unintentional

transmission.

◆

When the Slave receives data using the VFO programmed with a

simplex frequency, the received data replaces the data on both

VFOs. On the Slave, both RIT and XIT are set to OFF.

◆

When the Slave receives data using the VFOs programmed with

split frequencies, the received data replaces the data only on the

TX side of the VFO. On the Slave, XIT is set to OFF but RIT is

not changed.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood TS-2000E Seite 88

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info