Bedienungsanleitung Kenwood TS-2000E (Seite 89 von 150) (Englisch)

45743

Zoom out

Zoom in

Vorherige Seite

1/150

Nächste Seite

15 OPERATOR CONVENIENCES

COMPUTER CONTROL

By connecting this transceiver to a computer, you can

change the computer into an electronic console from

which you can remotely control functions of the

transceiver. This capability makes remote operation

of your transceiver possible from across the room,

from another room, or when coupled with other

commercially available products and where lawful,

from another city, state, or country via a telephone

connection.

Note:

◆

You can use the front panel controls while using computer

control. Settings done from the front panel are effective

immediately.

◆

After the computer is disconnected or turned off, all values and

settings on the front panel are restored.

SETTING UP

■ Equipment Needed

• A PC equipped with an RS-232C serial port.

• One straight cable. This cable must have a 9-pin

D-Sub RS-232C female connector at one end, and

at the other end a 9-pin or a 25-pin D-Sub

RS-232C female connector that mates with the

RS-232C port of your computer.

• Transceiver control application.

To design your programs, consult “APPENDIX” for the

necessary information.

■ Connections

Connecting the transceiver to the computer is easy.

See the diagram given in “CONNECTING

PERIPHERAL EQUIPMENT” {page 93}.

Note: Before connecting this transceiver to the computer, switch

OFF the power to both the transceiver and the computer.

COMMUNICATION PARAMETERS

In order to control the transceiver by computer, you

must first choose the communication parameters.

1 On the computer, configure your transceiver

control application for 8 data bits, 1 stop bit and

no parity.

2 On the transceiver, select the same transfer rate

and number of stop bits via Menu No. 56.

• The defaults are 9600 bps and 1 stop bit.

Note: To reliably use the 38400 or 57600 bps transfer rates, the

RS-232C port of the computer must support these high-speed

communications parameters.

REMOTE MICROPHONE CONTROLLER

If you have a DTMF microphone, you can use the

microphone as a wired remote control unit as

described below.

1 Plug the DTMF microphone into the microphone

connector of the transceiver.

2 Press [MENU], then turn the MULTI/ CH control to

access Menu No. 45D.

3 Press [+] to select ON.

4 Press [MENU] to store the setting and exit Menu

mode.

The DTMF keys function as follows:

FMTD

yek

noitcnuF

CNUF

edom

FMTD

yek

noitcnuF

CNUF

edom

1nacS–9

hcleuqS

nwoD/pU

–

/enoT

/SSCTC

SCD

edoC

tceleS

RWP

nwoD/pU

–

3VERTFIHSATNE–

4zHM–BLRTC

/NIAM

BUS

5INOM

KCOL

CretaepeR–

61ecioV

KCOL

FFO

DCNUF

CNUF

FFO

7emuloV

–nwoDnwoD

8dnaB

–# pUpU

Use the [#] (Up) and [ ](Down) keys to change the settings of

these functions.

The LOCK function is for the microphone keypad.

Note:

◆

Microphone Remote does not function while transmitting.

◆

You can use the DTMF Memory function {page 75} with the

Microphone Remote function.

◆

The Repeater function is available for K-type models only.

◆

Normally, pressing [2] cycles through Tone, CTCSS, DCS, and

OFF. However, if 1750 Hz is selected for Tone, pressing [2] will

only transmit the 1750 Hz tone. To return to Tone/ CTCSS/ DCS

mode, you must first deselect 1750 Hz for Tone.

◆

Press [D] to enter FUNC mode, to use the 2nd function of the

DTMF keys. Pressing [D] while in FUNC mode will exit FUNC

mode.

◆

[FUNC] on the transceiver works independently from the

Microphone Remote [FUNC] key.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood TS-2000E Seite 89

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info