Bedienungsanleitung Kenwood TS-480SAT (Seite 65 von 104) (Englisch)

511243

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

12 SCAN

VGROUP–9). As you select the Memory Channel,

“on” or “oFF” appears on the main frequency

display. “on” signifies that the memory channel is

active for the Program Scan and “oFF” signifies

that the memory channel group is inactive for the

Program Scan.

4 To activate the Program Scan frequency range,

select the desired VGROUP number by turning the

MULTI control. Then, press [ ] to select “on” for

the VGROUP (channel). When a channel is

activated for the Program Scan, “on” appears on

the display.

Note:

At least one of the valid Program Scan channels (from 90 to

99) must be programmed and selected to perform the Program Scan.

If no VGROUP (memory channel 90 ~ 99) is selected for the Program

Scan, the transceiver performs the VFO Scan {above}.

5 Press [SCAN/ SG.SEL] or [MTR/ CLR] to return

to the current VFO mode.

6 Press [SCAN/ SG.SEL] to start the Program

Scan.

•To quickly move towards a desired frequency

while scanning, turn the Tuning control or the

MULTI control, or press Mic [UP]/ [DWN].

•Turning the RIT/ XIT control clockwise

decreases the scan speed and

counterclockwise increases the speed, except

while in FM mode. The current scan speed is

shown on the display; P1 is the fastest speed

and P9 is the slowest.

• While in FM mode, Scan automatically stops

on a frequency where a signal is present. The

transceiver will either remain on that channel

for a short time (Time-Operated mode) or until

the signal drops out (Carrier-Operated mode),

depending on which mode you select via Menu

No. 11 {page 58}.

7 To stop Scan, press [SCAN/ SG.SEL] or

[MTR/ CLR].

Note:

◆

If you have turned the

SQL

control clockwise, far beyond the

squelch threshold while in FM mode, Scan may fail to stop at a

channel where a signal is present. If this happens, turn the

SQL

control slightly counterclockwise.

◆

If you press

[SCAN/ SG.SEL]

before storing any frequency range

for memory channels 90 to 99, the transceiver starts VFO scan.

◆

When the current receive frequency is within one of the ranges

that you selected with channel numbers, Scan starts with the

current frequency. The operating mode stored in the memory

channel is used.

◆

The operating mode can be changed while scanning, but the

memory channel is overwritten with the changed mode.

◆

When the current Scan range is smaller than a single step of the

MULTI

control, turning the control clockwise causes Scan to jump

to the start frequency, and counterclockwise to the end

frequency.

◆

Starting Program Scan switches OFF the RIT

and XIT functions.

◆

While in FM mode, the Program Scan monitors rounded off

frequencies regardless of the Menu No. 05 setting.

PROGRAM SCAN PARTIALLY SLOWED

You can specify a maximum of 5 frequency points for

each memory channel from 90 to 99 so that the

Program Scan slows down the scanning speed. To

specify the slow down frequency points, first program

the start and end frequencies into a memory channel

(90 ~ 99) {page 53}.

1 Access Menu No. 08 to confirm that the function is

ON (default is ON).

2 You can further configure the slow down frequency

width. Access Menu No. 09 to select the range

from 100 Hz to 500 Hz (default is 300 Hz).

Note:

If you select, for example, 500 Hz for Menu No. 09, the

Program Scan slows down to a

500 Hz width, centering the

frequency you marked below.

3 Press [A/B / M/V] (1 s) and turn the MULTI control

to recall the memory channel (90 ~ 99) for which

you want to specify the scan slow down

frequencies.

4 Press [ ]/ [ ] to confirm the start ([ ]) or end

([ ]) frequency.

5 Turn the Tuning control to the center frequency

point that you want the Program Scan to slow

down. Press [QMI/ M.IN] to mark the slow down

frequency point. The “ ” icon appears.

6 Repeat step 5 to specify the center slow down

frequency points. You can specify a maximum of

5 frequency points for each channel.

7 If you want to clear a slow down frequency point

that you previously stored, select the frequency

that you stored. Press [QMI/ M.IN] at this

frequency spot where “ ” appears.

•A confirmation beep sounds and the

transceiver “ ” disappears.

• If you want to clear all the slow down frequency

points at once, perform the Channel \

Channel Transfer to overwrite the memory data

to the same memory channel {page 52}. This

operation removes all the frequency points that

you stored.

8 Press [A/B / M/V] to return to VFO mode.

9 Press [SCAN/ SG.SEL] to start the Program Scan

with the slow down frequency point(s).

Note:

◆

During the Program Scan, you can turn the

RIT/ XIT

control to

adjust the scanning speed. Turn the control clockwise/ counter-

clockwise to slow down/ speed up the scan. The Program Scan

speed indicator appears on the main dot-matrix display during

the Program Scan; P1 is the fastest speed and P9 is the slowest.

◆

You cannot change the Program Scan speed in FM mode.

◆

You can specify the Program Scan slow down frequency point in

FM mode but it does not function.

SCAN HOLD

This function stops Program Scan for approximately

5 seconds, then resumes Scan when you jump to the

desired frequency by turning the Tuning control or the

MULTI control, or by pressing Mic [UP]/ [DWN].

To use this function, access Menu No. 10, and select

“on”. The default is OFF.

Kenwood TS-480SAT Seite 65

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood TS-480SAT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info