Bedienungsanleitung Kenwood TS-480SAT (Seite 66 von 104) (Englisch)

511243

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

12 SCAN

MEMORY SCAN

Memory Scan monitors all memory channels in which

you have stored frequencies (All-channel Scan) or only

a desired group of memory channels (Group Scan).

Scan automatically stops at a channel where a signal

is present, regardless of the operating mode. The

transceiver will either remain on that channel for a

short time (Time-Operated mode) or until the signal

drops out (Carrier-Operated mode). Use Menu No.

11 to select the mode. The default is “to” (Time-

Operated).

SCAN RESUME METHOD

The transceiver stops scanning at the frequency (or

memory channel) where a signal is detected. It then

continues scanning according to which resume mode

you have selected. You can choose one of the

following modes. The default is Time-operated mode.

•Time-Operated mode (“to”)

The transceiver remains on a busy frequency (or

memory channel) for approximately 6 seconds,

then continues to scan, even if the signal is still

present.

• Carrier-Operated mode (“co”)

The transceiver remains on the busy frequency (or

memory channel) until the signal drops out. There

is a 2 second delay between signal dropout and

scan resumption.

1 Press [MENU/ F.LOCK] to enter Menu mode.

2 Turn the MULTI control to select Menu No. 11.

3 Press [ ]/ [ ] to select “to” (Time-Operated) or

“co” (Carrier-Operated).

4 Press [MENU/ F.LOCK] to complete the setting

and exit Menu mode.

You can lock out the memory channels that you

prefer not to monitor while scanning. To do this, refer

to “Memory Channel Lockout” {page 54}.

ALL-CHANNEL SCAN

Use the following procedure to scan all the memory

channels that contain frequency data in sequence,

ignoring the Memory Group number.

1 Select Time-operated or Carrier-operated mode

via Menu No. 11.

2 Press [A/B / M/V] (1 s) to enter Memory Recall

mode.

3 Turn the SQL control to adjust the squelch

threshold to mute the speaker.

4 Press [SCAN/ SG.SEL] (1 s) to enter Scan Group

Select mode.

•Turn the MULTI control to select the Memory

channel group.

• MGROUP–0 represents Memory channel 0 ~

9, MGROUP–1 represents Memory channel 10

~ 19 and so on up to MGROUP–9 which

represents Memory channel 90 ~ 99 {page 53}.

5 As you select the Memory Groups using the

MULTI control, press [ ] to select “oFF” for all

Memory Groups.

6 Press [SCAN/ SG.SEL] to return to Memory

Recall mode.

7 Press [SCAN/ SG.SEL] to start All-channel Scan.

• Scan starts from the current memory channel

and ascends up through the channel numbers.

(The scan direction cannot be changed.)

•To jump to a desired channel while scanning,

turn the MULTI control, or press Mic [UP]/

[DWN].

8 To stop Scan, press [SCAN/ SG.SEL] or

[MTR/ CLR].

Note:

◆

If you have turned the

SQL

control clockwise, far beyond the

squelch threshold, Scan may fail to stop at a channel where a

signal is present. If this happens, turn the

SQL

control slightly

counterclockwise.

◆

Starting Memory Scan switches OFF the RIT and XIT functions.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood TS-480SAT Seite 66

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood TS-480SAT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info