Bedienungsanleitung Kenwood TS-480SAT (Seite 79 von 104) (Englisch)

511243

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

13 OPERATOR CONVENIENCES

■ Voice Guide Announcement Volume

Turning the AF control does not change the volume

for the Voice Guide announcement volume. To

change the announcement volume , access Menu

No. 15 to select the volume level from “1” to “7” or

“oFF”.

■ Voice Guide Announcement Speed

If you feel the Voice Announcement speed is too slow

or fast, you can adjust the Voice Announcement

speed. Five different speed can be configured.

Access Menu No. 16 and select “0” to “4”. 0 is the

slowest speed and 4 is the fastest speed. The default

speed is 1.

CROSSBAND REPTEATER

If you have a TM-D700 transceiver and another VHF

or UHF transceiver, you can set up the TS-480

transceiver and TM-D700 transceiver as a crossband

repeater. The TM-D700 will receive signals you

transmit from the additional VHF or UHF transceiver

when both transceivers are set with the same

frequency. The signal is then routed to the TS-480

transceiver and retransmitted on the frequency you

have set upon the TS-480 transceiver. Likewise,

signals received on the TS-480 transceiver are routed

to the TM-D700 and retransmitted to the transceiver

you have with you, allowing you to hear the received

call in a distant location.

To interface between the TS-480 transceiver and

TM-D700 transceiver, refer to “CROSSBAND

REPEATER” for details {page 79}.

You need a cable that has mini-DIN (6-pin) male

connector at both ends.

Note:

For the repeater function to operate, the squelch levels of both

transceivers (TS-480 and TM-D700) must be adjusted properly so

that no background noise can be heard. Because the transmission is

controlled by monitoring the squelch status only.

Operation

The crossband repeater function uses 2 frequency

bands to receive and transmit signals. When a signal

is received on one band, it is retransmitted on the

other band.

1 Select a desired transmission/ reception VHF or

UHF frequency on the TM-D700 transceiver.

2 Confirm PTT icon is visible on the crossband

repeater frequency on the TM-D700 transceiver.

3 Select the same frequency for the terminal

transceiver.

4 Select a desired HF/ 50 MHz frequency on the

TS-480 transceiver.

5 Adjust the squelch threshold level so that both

TS-480 transceiver and TM-D700 transceiver

mute.

6 Press [MENU/ F. LOCK] on the TS-480, then turn

MULTI control to access Menu No. 57.

7 Press [ ] to select “on”.

• When the TS-480 transceiver’s squelch opens,

the TM-D700 transceiver retransmits the

incoming audio signal on the VHF or UHF

frequency at the same time.

•When the TM-D700 transceiver’s squelch

opens, the TS-480 transceiver retransmits the

incoming audio signal on the HF/ 50 MHz

frequency.

8 Access Menu Nos. 46 and 47 and press [ ]/ [ ]

to adjust the input/ output audio level.

9 To quit the TM-D700 repeater operation,

disconnect the interface cable between

transceivers and access Menu No. 57 on the

TS-480 transceiver and select “oFF”.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood TS-480SAT Seite 79

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood TS-480SAT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info