Bedienungsanleitung Kenwood TS-480SAT (Seite 77 von 104) (Englisch)

511243

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

13 OPERATOR CONVENIENCES

MESSAGE PLAYBACK

You can play back the message in channel 1, 2, or 3

to check or to send. It is also possible to make a

longer message by consecutively playing back the

messages of more than one channel, linking them

together.

You can even repeatedly send a longer, linked

message by using the Repeat function. To switch this

function ON, access Menu No. 31 and select “on”

(default is OFF). Then, select the repeat interval time

in Menu No. 32 (default is 10 seconds).

Note:

◆

Pressing

[ ]

(POWER) cancels playback in progress.

◆

The settings in Menu Nos. 31 and 32 are shared with CW

Message Playback described in “CW MESSAGE MEMORY”

{page 40}.

■ Checking Messages

1 Select SSB, FM, or AM mode.

• Select the same mode when you recorded

the message.

•Confirm the VOX function is OFF.

2 Press [CH1/ 1/ REC], [CH2/ 2/ REC], or

[CH3/ 3/ REC], depending on which channel

you want to check.

• For example, “AP 1– –” appear while playing

back the message in channel 1.

•To interrupt playback, press [MTR/ CLR].

3 To play back another message in sequence,

press the corresponding key ([CH1/ 1/ REC],

[CH2/ 2/ REC], or [CH3/ 3/ REC]) while the

first message is being played.

• Up to 3 channels can be queued.

■ Sending Messages

1 Select SSB, FM, or AM.

• Select the same mode when you recorded

the message.

2 Press [VOX/ 8] to switch VOX ON or OFF.

• If you switched VOX ON, skip step 3.

3 Press and hold Mic [PTT].

4 Press [CH1/ 1/ REC], [CH2/ 2/ REC], or

[CH3/ 3/ REC], depending on which channel

you want to use.

• For example, “AP 1– –” appear while playing

back the message in channel 1.

•To interrupt playback, press [MTR/ CLR].

5 To play back another message in sequence,

press the corresponding key ([CH1/ 1/ REC],

[CH2/ 2/ REC], or [CH3/ 3/ REC]) while the

first message is being played.

•Up to 3 channels can be queued.

6 Release Mic [PTT].

■ Erasing a Recorded Message

1 Press [CH1/ 1/ REC] (1 s) or

[CH2/ 2/ REC] (1 s) or [CH3/ 3/ REC] (1 s) to

select the message which you want to erase.

• “APn – –” appear, where “n” represents the

channel number.

2 To erase the recorded message, press and

hold the same key as in step 1 ([CH1/ 1/ REC],

[CH2/ 2/ REC], or [CH3/ 3/ REC]), while

simultaneously pressing [MTR/ CLR].

•A beep sounds and the message is erased.

■ Changing Inter-message Interval Time

For repetitive message playback, you can change

the interval between each series of messages.

Use Menu No. 32, and select the time in the range

of 0 to 60 seconds.

■ Changing Message Playback Volume

Turning the AF control does not change the

volume for the message playback. To change the

message playback volume , access Menu No. 14

to select the playback volume level from “1” to “9”

or “oFF”.

CONSTANT RECORDING

By utilizing the digital recording capability of the

VGS-1, you can configure the VGS-1 to store the last

30-second of the incoming reception signal to the

VGS-1. It is similar to a flight recorder that is used in

an aircraft. You can play back the last 30 seconds of

the reception signal to confirm what has been heard.

To activate the Constant Recording function, access

Menu No. 30 and select “on”. “ ” appears and the

the transceiver starts recording the signal in

background. When you press [CH3/ 3/ REC] (1 s),

the VGS-1 stores a maximum of last 30-second of the

reception audio signal to the flash memory. While

writing the audio signal data to flash memory, “FLASH

WR” appears for a while. To playback the stored

reception signal, press [CH3/ 3/ REC].

To play back the stored reception sound, press

[CH3/ 3/ REC]. To quit, press [MTR/ CLR].

Note:

◆

While the Menu No. 30 is ON, you cannot use the Channel 3

(CH3) message memory to record and playback your voice

message. However, the message in CH3 is not erased. When

the Constant Recording function is turned OFF (Menu No.30 is

OFF), you can playback the message on Channel 3 (CH3).

◆

While the “ ” icon disappears, such as the VGS-1 is playing

back a message or the Voice Guide function is working, the

Constant Recording function temporarily pauses.

◆

When you record a new message to the VGS-1, 30-second

Constant Recording buffer is cleared.

◆

You cannot transmit a stored audio signal that is recorded with

the Constant Recording function.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood TS-480SAT Seite 77

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood TS-480SAT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info