Bedienungsanleitung Kenwood TS-480SAT (Seite 75 von 104) (Englisch)

511243

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

13 OPERATOR CONVENIENCES

COMPUTER CONTROL

By connecting this transceiver to a computer, you can

change the computer into an electronic console from

which you can remotely control functions of the

transceiver. This capability makes remote operation

of your transceiver possible from across the room,

from another room, or when coupled with other

commercially available products and where lawful,

from another city, state, or country via a telephone

connection.

Note:

◆

You can use the Remote Control panel controls while using

computer control. Settings done from the Remote Control panel

are effective immediately.

◆

After the computer is disconnected or turned off, all values and

settings on the Remote Control panel are restored.

SETTING UP

■ Equipment Needed

•A PC equipped with a COM (serial) port

• One straight cable. This cable must have a DB-9

female connector at one end, and a DB-9 or a

DB-25 female connector that mates with the COM

port of your computer at the other end.

•Transceiver control application

To create your programs, access the KENWOOD

website (http://www.kenwood.com/i/products/info/

amateur.html) and download the TS-480HX/ SAT

command reference documents (PDF format) for

details.

■ Connections

Connecting the transceiver to the computer is easy.

Refer to the diagram in “CONNECTING

PERIPHERAL EQUIPMENT” {page 76}.

Note:

Before connecting this transceiver to the computer, switch

OFF the power to both the transceiver and the computer.

COMMUNICATION PARAMETERS

In order to control the transceiver by computer, you

must first choose the communication parameters.

1 On the computer, configure your transceiver

control application for 8 data bits, 1 stop bit, and

no parity.

2 On the transceiver, select the same transfer rate

via Menu No. 56.

• The defaults are 9600 bps and 1 stop bit.

• 4800 bps is used for the Master/ Slave

operation only (Parity ON and 2 stop bits).

1 Switch ON the Transfer function of each

transceiver.

• On the TS-480HX/ SAT, access Menu No. 53

and select “on”. For the compatible

transceiver, refer to the instruction manual that

came with the transceiver.

2 On the Slave, access Menu No. 54 and select

either “oFF” (QUICK MEMO channel 0) or “on”

(the VFO).

• The default is OFF (QUICK MEMO).

3 On the Master, perform the appropriate operation

to send data.

• For the correct method, refer to the instruction

manual that came with the transceiver.

Note:

◆

If you always use the TS-480HX/ SAT for receiving only, activate

the TX Inhibit function, accessing Menu No. 55 to avoid

unintentional transmission.

◆

When the Slave receives data using the VFO programmed with a

simplex frequency, the received data replaces the data on both

VFOs. On the Slave, both RIT and XIT are set to OFF.

◆

When the Slave receives data using the VFOs programmed with

split frequencies, the received data replaces the data only on the

TX side of the VFO. On the Slave, XIT is set to OFF but RIT is

not changed.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood TS-480SAT Seite 75

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood TS-480SAT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info