Bedienungsanleitung Kenwood TS-480SAT (Seite 74 von 104) (Englisch)

511243

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

13 OPERATOR CONVENIENCES

TX TUNE

The TX Tune function allows you to adjust the

antenna length, or tune the linear amplifier while

transmitting a continuous CW signal.

To use the TX Tune function, first assign the function

to a PF key on the Remote Control panel (or Mic PF

keys) {page 64}.

1 Press [MENU/ F.LOCK] and turn the MULTI

control to select Menu No. 48.

2 Press [ ]/ [ ] to select “67”.

3 Press [MENU/ F.LOCK] to store the setting and

exit the Menu mode.

4 Press [PF].

• The transceiver automatically switches to CW

mode, and transmits a continuous carrier.

The transceiver selects the SWR meter

function automatically.

• While in TX Tune mode, most keys are

disabled.

• The default output power is configured as

10 watts. However, you can adjust the output

power using [PWR/ 4/ TX MONI] and the

MULTI control if necessary. The transceiver

stores the new output power setting when you

exit the TX Tune mode.

5 Press [PF] again to exit the TX Tune mode.

QUICK DATA TRANSFER

This transceiver has the capability to quickly and

conveniently transfer the reception frequency and

mode to another compatible transceiver. Compatible

transceivers include:

• TS-480HX/ SAT • TS-2000

• TS-570S/ 570D • TS-870S

Data transfer could be useful while contesting. A

spotting station that is searching for new contest

multipliers can quickly transfer a frequency over to

the running (main) station.

SETTING UP

■ Equipment Needed

In addition to a compatible transceiver, the following

equipment is required:

Transfer to TS-480HX/ SAT, TS-2000, TS-570, or

TS-870S:

• One cross-wired cable. This cable must have a

DB-9 female connector at both ends.

■ Connections

For diagrams on how to connect the 2 transceivers,

refer to “CONNECTING PERIPHERAL EQUIPMENT”

{page 76}.

USING QUICK TRANSFER

When connecting with another TS-480HX/ SAT,

TS-2000, TS-570, or TS-870S, use the same COM

connector baud rate on each transceiver.

Note:

While transferring data, other functions may work slower.

■ Transferring Data

The TS-480HX/ SAT transceiver works as the Master,

sending data to the Slave transceiver.

1 Turn ON the Transfer function of each transceiver.

•On the TS-480HX/ SAT, access Menu No. 53

and select “on”. For the compatible

transceiver, refer to the instruction manual that

came with the transceiver.

2 On the Master, while in VFO mode, select an

operating frequency and mode.

3 On the Master, press [QMI/ M.IN].

• When using another TS-480HX/ SAT as the

Slave, “PC” appears on the Slave.

• The displayed data is stored in Quick Memory

channel 0 on the Master and transferred to the

Slave.

Note:

If the Master has RIT switched ON, the offset frequency is

added to the reception frequency to be transferred.

■ Receiving Data

The TS-480HX/ SAT transceiver works as the Slave,

receiving data from the Master transceiver. The

Slave can receive data using either Quick Memory

channel 0 or the VFO.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood TS-480SAT Seite 74

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood TS-480SAT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info