Bedienungsanleitung Kenwood TS-480SAT (Seite 76 von 104) (Englisch)

511243

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

13 OPERATOR CONVENIENCES

CONTROLLING THE TS-480 FROM PC

If a PC and the TS-480HX/ SAT are connected using

a serial cable {page 76}, you can remotely control the

functions of the TS-480 from a PC. Download the

free ARCP-480 software from the following URL.

http://www.kenwood.com/i/products/info/amateur.html

The detailed remote controlling instructions are

available in accompanied documents and help file.

REMOTE CONTROLLING THE TS-480 ON THE

NETWORK

In addition to the ARCP-480 program, the ARHP-10

program can also be downloaded from the above

site. This ARHP-10 program is a ARCP-480 host

program that allows a user who is connected in the

network to remote control the TS-480 transceiver

from a distant location. If you make interface cables

that transfer the audio between the TS-480

transceiver and PC on the host transceiver, you can

receive signals and transmit your voice over the

network. For detailed information, download the

ARHP-10 program and consult accompanied

documents.

VGS-1 VOICE GUIDE & STORAGE UNIT

(OPTIONAL)

The optional VGS-1 unit allows you to record a

maximum of 30-second voice message to 3 different

memory channels. After recording a message via

your transceiver microphone, you can then transmit

those recorded messages. It also announces the key

function and frequencies each time you press a key

(Voice announcement). Since the incoming reception

signal is processed in digital data in the transceiver,

the VGS-1 can be configured to store the incoming

audio signals constantly in the background. If you

wish, you can store the last 30-second of the

incoming signal to the VGS-1 for the later playback

(Constant recording).

For information on how to install the VGS-1 unit, refer

to “INSTALLING OPTIONS” {page 81}.

RECORDING MESSAGES

This section explains how to record a single

message.

1 Select SSB, FM, or AM mode {page 19}.

• Select a mode that you wish to transmit.

2 If VOX is ON, press [VOX/ 8] to switch the

function OFF.

3 Press [CH1/ 1/ REC] (1 s) to record the message

for channel 1.

• BT in Morse code sounds and “AP1 –”

appears.

•To quit recording your message, press

[MTR/ CLR].

4 Press and hold [CH1/ 1/ REC], then begin

speaking into your microphone.

• Three channels are available for recording

messages. Press channel key [CH2/ 2/ REC]

or [CH3/ 3/ REC] in place of [CH1/ 1/ REC], in

step 3, to record the message on a different

channel.

• While the Constant Recording is working, CH3

is unavailable for the message recording.

5 Release the key pressed in step 4 when you have

finished recording your message.

• Also when the maximum recording time

passes, recording automatically stops.

• The contents of the channel is overwritten with

the new message.

• “FLASH WR” appears while the transceiver is

storing the message data to the VGS-1 flash

memory.

6 Repeat steps 3 to 5 to record a message on

another channel.

Note:

Pressing

[ ]

(POWER) cancels recording in progress and

clears the memory channel.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood TS-480SAT Seite 76

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood TS-480SAT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info