Bedienungsanleitung Kenwood TS-590SG (Seite 91 von 96) (Englisch)

606692

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

TROUBLESHOOTING 15

Problem Probable Cause Corrective Action Page

A message cannot be

recorded/ played back

or no announcement

can be heard.

There is a communication error

between the transceiver and

the VGS-1.

Conﬁ rm that the connector of the VGS-1 is

securely connected to the transceiver. Perform

the Full reset. If the problem persists, contact a

KENWOOD authorized service center for repairs

(with the VGS-1 attached).

76,83

The transceiver

output power seems

to be low in SSB

mode.

Most of the external RF

power meters measure the

average RF power. So, the

meter reading is low when

you operate and talk in SSB

mode. The LCD meter used

in the TS-590SG has relatively

fast response time but it is not

fast enough to measure the

accurate PEP (Peak Envelope

Power).

Apply a continuous single tone (1 kHz) to the

microphone audio input to measure the RF

output power. The PEP will be the same as this

RF output level.

—

The PC and external

equipment is not

modulating.

The input terminal is different

from the one speciﬁ ed (Menu

No. 69) for the external

equipment.

Conﬁ rm that the setting of Menu No. 69 matches

the input terminal for the external equipment.

MICROPROCESSOR RESET

If your transceiver seems to be malfunctioning,

resetting the microprocessor to its default settings may

resolve the problem. There are 2 levels of resetting

the microprocessor of the TS-590SG transceiver:

Partial Reset and Full Reset.

INITIAL SETTINGS

For each VFO, the factory defaults for the operating

frequency and mode are as follows:

• VFO A: 14.000.00 MHz/ USB

• VFO B: 14.000.00 MHz/ USB

The Memory channels and Quick Memory channels

have no data stored.

VFO RESET

Perform a VFO Reset if a key or control does not

function according to the instructions in this manual.

The following data is NOT erased by performing a

VFO Reset.

• Memory channel data

• Menu settings

• Antenna tuner preset data

• ANT 1/ ANT 2 selection data

• Frequency and mode data for the Auto Mode

function

• Various adjustment setting values

1 Turn the transceiver power OFF.

2 Press [A/B (A=B)] + [

] to switch the transceiver

ON.

• A conﬁ rmation message appears on the display.

3 Turn the MULTI/CH control and select “VFO

RESET”.

4 Press [A/B (A=B)] to perform the VFO reset.

• A conﬁ rmation message appears when

performing the VFO Reset. Press [A/B (A=B)]

again to proceed. Otherwise, press any other

key to cancel the VFO Reset and return to

normal operation.

• The VFOs reset to the factory default values.

FULL RESET

Perform a Full Reset if you want to erase all the data

in all the memory channels. In addition, this function

resets all the settings that you customized, to the

factory defaults (i.e.- menu settings, antenna tuner

preset data, etc.).

1 Turn the transceiver power OFF.

2 Press [A/B (A=B)] + [ ] to switch the transceiver

ON.

• A conﬁ rmation message appears on the display.

3 Turn the MULTI/CH control and select “FULL

RESET”.

4 Press [A/B (A=B)] to perform the Full reset.

• A conﬁ rmation message appears when

performing the Full Reset. Press [A/B (A=B)]

again to proceed. Otherwise, press any other

key to cancel the Partial Reset and return to

normal operation.

• All frequencies, modes, memory data,

adjustment values, and AT preset data are set

to the factory default values.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood TS-590SG Seite 91

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood TS-590SG

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info