Bedienungsanleitung Kenwood TS-870S (Seite 55 von 104) (Englisch)

606693

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

AGC AUTO

LSB

AUTOMATIC ANTENNA TUNER

You have the choice of using the internal tuner, an

external AT-300 tuner, or both.

Note:

◆

The antenna tuners will not tune outside the authorized transmit

limits of Amateur bands.

◆

If an external AT-300 tuner is connected, the internal tuner is

bypassed when the ANT 1 connector is selected. The AT-300

cannot be used with the ANT 2 connector.

◆

When tuning in CW mode, the SWR meter may deflect upscale

momentarily. This is not a fault.

◆

If using Full Break-in CW, the internal antenna tuner can be

bypassed completely or can be in-line for both transmitting and

receiving. Even when OFF is selected via Menu No. 08 (RX AT),

received signals pass through the antenna tuner. To protect the

antenna tuner relay, the tuner cannot be used only for

transmitting.

PRESETTING (INTERNAL TUNER ONLY)

After each successful tuning session, the Preset

function stores the data for the position of the tuning

capacitors on each band. Then, if the frequency is

changed while the internal tuner is switched ON, this

function automatically positions the capacitors without

need for retuning.

After changing bands, the Preset

function activates for the newly selected band.

A different set of data is stored for each of the

18 antenna tuner bands (see table) and for each

antenna connector (ANT 1 and ANT 2). Therefore,

enabling the other antenna connector by pressing the

[ANT] button may also cause the Preset function to

activate. If no Preset data exists for a particular band/

antenna combination, then the default data for 50 Ω is

stored.

Presetting does not activate while transmitting. For

split-band operation, even if Menu No. 08 (RX AT) is

ON, the antenna tuner is bypassed while receiving.

Also, at all times, presetting is only done for transmit

frequencies.

PRESET BANDS FOR INTERNAL TUNER

Note:

The lower limit is inside the band in each case; the higher

limit is inside the next higher band. For example, 14.1 MHz is in

Band 12 whereas 14.49 MHz is in Band 13 (exception: 30 MHz is in

Band 18).

7 OPERATING AIDS

INTERNAL TUNER

Note:

Setting Menu No. 33 (TUN.WIDE) to OFF to select an

SWR

≤

1.2:1 reduces internal tuner losses. This setting is best.

1 Press [THRU/AUTO].

•“–AT – TX” lights. If Menu No. 08 (RX AT) is ON,

then “– AT – TX RX” lights indicating that the

tuner is in-line while transmitting and receiving.

In this case, prior to tuning in Step 2, received

signals are attenuated and the receiver sensitivity

is lowered.

• If the tuner has not adjusted itself yet for the

selected frequency, then AT TUNE lights, and

Preset tuning begins. Signals pass through the

antenna tuner during this time. If Menu No. 08

(RX AT) is OFF, the antenna tuner is bypassed.

The AT TUNE light goes out when presetting is

completed. You cannot transmit while presetting

is in progress.

• If Preset data exists, the next step cannot be

done until the transceiver completes the Preset

tuning.

2 Press [AT TUNE].

• To cancel tuning for any reason, press

[THRU/AUTO] or [AT TUNE].

• If the Preset tuning is aborted by pressing

[AT TUNE], the new temporary data will be used,

but this new data does not update the stored

Preset data. Also, the new temporary data will be

lost if the operating band is changed. Return to

the stored Preset data by pressing

[THRU/AUTO] OFF and then ON again.

• AT TUNE lights and stays lit while the tuner

tunes. When the light goes out, the tuner has

successfully matched the transceiver to the

antenna system with an SWR less than the value

set in Menu No. 33 (TUN.WIDE). You can begin

operating.

• If tuning doesn’t finish within about 20 sec, an

alarm sounds. You may stop the alarm and the

tuning by pressing [AT TUNE]. The alarm can be

either a triple beep or the Morse code “CHECK”

depending on the Menu No. 37 (WARN. BP)

setting.

• After each successful tuning, the Preset data is

updated.

Note:

◆

While receiving with Menu No. 08 (RX AT) ON on

frequencies outside the Amateur bands, sensitivity is

lowered.

◆

It’s a good practice to press

[AT TUNE]

after changing bands

to ensure the tuner has tuned for minimum SWR.

AT TUNE

7.49 ~ 10.49

10.49 ~ 14.1

14.1 ~ 14.49

14.49 ~ 20.99

20.99 ~ 21.15

21.15 ~ 21.99

21.99 ~ 25.49

25.49 ~ 29

29 ~ 30

0.030 ~ 1.85

1.85 ~ 2.01

2.01 ~ 3.525

3.525 ~ 3.575

3.575 ~ 3.725

3.725 ~ 4.49

4.49 ~ 7.03

7.03 ~ 7.1

7.1 ~ 7.49

Range

(MHz)

Band

No.

Range

(MHz)

Band

No.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood TS-870S Seite 55

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood TS-870S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info