Bedienungsanleitung Kenwood TS-870S (Seite 54 von 104) (Englisch)

606693

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

USBAUTO

CWAUTO

7 OPERATING AIDS

3 Press [ENTER], then enter the frequency via the

keypad. Alternatively, you can enter the frequencies

by using the Tuning control or Mic [UP]/[DWN].

Pressing [UP] or [DOWN] on the Front Panel

changes the frequency in 1 MHz steps.

•“– –.– – 0.00” appears if [ENTER] is pressed.

• The 10 kHz digit is the least significant that can

be entered therefore boundaries must be

multiples of 10 kHz.

• Four digits must be entered. However, if

[ENTER] is pressed after beginning to enter

digits, 0 is entered automatically for the remaining

un-entered digits, and frequency entry is

completed.

• If you enter a wrong digit, press

[CLEAR], [ENTER] then re-enter the entire

frequency.

4 Press [LSB/USB] or [CW/–R] or [FSK/–R] or

[FM/AM] to select the mode for this boundary.

5 Repeat Steps 2 ~ 4 for each boundary that you want

to change.

6 Press [CLR] to exit from this mode.

• Switching the power OFF before pressing [CLR]

results in loss of the entered data.

USING AUTOMATIC MODE

Toggle Automatic Mode ON or OFF via Menu No. 34

(AUT.MODE). The default is OFF. When Automatic

Mode is ON, you can always change the mode

manually by pressing a Front Panel MODE button. An

Automatic Mode boundary must be crossed for the

mode to automatically change.

Automatic Mode does not work if you change bands by

pressing [UP] or [DOWN]. Instead, the mode last used

on the newly selected band will be recalled from the

band memory. Switching ON the 1MHz Step function

will allow Automatic Mode to work when using [UP] or

[DOWN].

In SSB mode when Automatic Mode is OFF, the

transceiver automatically selects LSB for frequencies

lower than 9.5 MHz, and selects USB for 9.5 MHz or

higher frequencies if the Tuning control or Mic

[UP]/[DWN] is used to cross the frequency of 9.5 MHz.

This is also true if using the Front Panel [UP] or

[DOWN] button. In all modes, the RIT or XIT frequency

shift is not taken into account by Automatic Mode. Also,

Automatic Mode will not function if a frequency is

entered via the keypad on the Front Panel.

AUTOMATIC MODE

Automatic Mode automatically selects the operating

mode according to a set of frequency and mode data

that you input. The purpose of Automatic Mode is for

the transceiver to select the correct mode for you as you

tune within a band. For Automatic Mode to work, you

must first program the frequency/mode relationships

that you want.

AUTOMATIC MODE BOUNDARIES

• The defaults for all boundaries are 30 MHz USB.

• Boundaries may only be changed (not deleted).

• The mode assigned to a boundary will be selected

while operating on all frequencies below that

boundary down to and including the next lower

boundary.

• Each boundary is numbered. As the boundary

numbers get larger, so must the boundary

frequencies.

Example: If Boundary No. 09 is 14.100 MHz, then

Boundary No. 10 must be a frequency larger by at

least 10 kHz than 14.100 MHz. The lowest

frequency that could be stored in Boundary No. 10 is

14.110 MHz. A lower frequency will not be accepted.

• Frequencies larger than the maximum receive

frequency cannot be stored.

• There is a maximum of 19 boundary frequencies.

• Automatic Mode is always “OFF” in the range from

the highest boundary to the maximum transceiver

frequency.

Example: If 18 MHz CW is stored in Boundary

No. 14, tuning to 18 MHz or higher selects USB

since the boundary default of 30 MHz USB is stored

in Boundary No. 15. Whereas, if 18 MHz CW is

stored in Boundary No. 18 (highest boundary),

tuning to a frequency lower than 18 MHz selects CW

but tuning to 18 MHz or higher will not change the

mode (still CW).

Use the following procedure to change a boundary.

1 Press [MENU]+[ ].

• Boundary No. 00 appears.

2 Turn the M.CH/VFO.CH control to select the

boundary that you want to change.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood TS-870S Seite 54

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood TS-870S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info