Bedienungsanleitung Kenwood TS-870S (Seite 52 von 104) (Englisch)

606693

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

USB

AGC AUTO MONI

USB

AGC AUTO PROC

8 Press [METER] to select the COMP function to allow

you to monitor the compression while transmitting.

9 To switch OFF the processor, press [PROC] again.

•“PROC” goes out.

Note:

Input audio that is controlled by the AGC will be clipped.

Therefore, when mixing audio with the operator’s voice, lower the

MIC

gain control as necessary.

CHANGING FREQUENCY WHILE TRANSMITTING

Moving your frequency while transmitting is usually an

unwise practice due to the risk of interference to other

stations. While transmitting, if you select a frequency

outside the transmit frequency range, the transceiver is

automatically forced to receive mode. If transmit was

selected using the [SEND] key, transmission will not be

resumed until you select a frequency inside the transmit

frequency range, and you transmit again.

TRANSMIT MONITOR

The Transmit Monitor function allows you to hear your

own transmitted signal.

Press [MONI] to toggle the Monitor function ON or OFF.

• To change the volume of the monitored audio,

adjust the MONI control.

7 OPERATING AIDS

SPEECH PROCESSOR (SSB/AM)

The speech processor functions by leveling the large

fluctuations in your voice when you speak. This leveling

action effectively raises the average transmit output

power resulting in a more understandable signal when

operating using SSB or AM. You will notice that using

the speech processor makes it easier to be heard by

distant stations.

1 Select SSB or AM mode.

2 Select the preferred processor characteristics via

Menu No. 25 (PROC.LOW) and Menu No. 26

(PROC.HI).

• You can customize the low and high ranges of

the speech envelope from –6 to +6 dB.

3 Press [PROC] to switch ON the processor.

•“PROC” lights.

4 Press [METER] to select the COMP function.

5 While speaking at your normal voice level, adjust the

PROC control for a level of 10 dB or less.

• Using higher compression will not improve your

signal clarity or apparent signal strength.

Excessively compressed signals are more

difficult to understand due to distortion and are

less pleasant to hear than signals with less

compression.

6 Press [METER] to select the ALC function.

7 The compression level affects the ALC setting for

SSB; therefore, while continuing to speak into the

microphone, adjust the CAR control for a reading

within the ALC zone.

• Keep the meter inside the ALC zone for the

cleanest transmit signal and to avoid interfering

with other stations on adjacent frequencies.

Mode

SSB

FSK

Unmixed AF

Keyed output from DSP with sidetone OFF

AF corresponding to the shift and mark/space

Unmixed AF

Transmit Sampling Point

-3

-6

Lower

Raise

Low

range

High

range

800 Hz 1.6 kHz

OFF

CAR DELAY

AGC KEY SPEED

METER PROC MONI

100

MIC

ATT

ANT DOWN UP

VOX FULL/SEMI

AT TUNE

SEND

THRU/AUTO

AIP

PHONES

PROC MONI

MIC PWR

M.IN

REC F.LOCK

CH 4 CLR

CH 3 SCAN

CH 2 M>VFO

CH 1 M.IN

ENTER TF-SET

FINE

1MHz

QUICK MEMO

SLOW FAST

SWR

PWR

FILTER

10 2

COMP

M.CH

USB CW R FSK FM AMLSBAUTO

FULLVOX SEMI AIP AGC AUTO PROC MONI

HF TRANSCEIVER TS-870

ON AIR AT TUNE

PROC

MONI

COMP

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood TS-870S Seite 52

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood TS-870S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info