Bedienungsanleitung Kenwood TS-870S (Seite 66 von 104) (Englisch)

606693

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

Scan is a useful feature for hands-off monitoring of your

favorite frequencies. After becoming comfortable with

how to use all types of Scan, the monitoring flexibility

gained will increase your operating efficiency.

This transceiver provides the following types of Scan:

PROGRAM SCAN

The Program Scan function scans the range between

the Start frequency and End frequency stored in

memory channel 99. If Program Scan is used before

you store a Start and an End frequency, then the lower

and upper frequency limits of the transceiver are

automatically stored for the Start and End frequencies

respectively. Some General market versions substitute

the lower and upper frequencies for the current band in

place of the frequency limits of the transceiver.

Program Scan direction is controlled by the Start and

End frequency relationship. The following table

summarizes the way that Program Scan functions:

SCAN

For a refresher on how to store the Program Scan

Limits, refer to “STORING SCAN LIMITS IN CH 99”

{page 58}. The following are additional important points

regarding the Program Scan function:

• Starting a transmission by closing the CW key, by

sending a packet, or by triggering the VOX circuit by

voice or the DRU-3 Digital Recording Unit stops

Program Scan; however, transmission does not

begin immediately.

• When the Program Scan range is smaller than a

single step of the M.CH/VFO.CH control, turning this

control causes Scan to jump to the lower of the

Start/End frequencies, then continue scanning.

• Starting the Program Scan function switches OFF

the RIT and XIT functions. RIT and XIT are not

switched ON again when Program Scan stops, and

the RIT/XIT offset frequency is not cleared.

•Operating mode can be changed while scanning.

• If Automatic Mode is switched ON, it will function

with the Program Scan function.

Use the following procedure to activate Program Scan.

1 Select the VFO mode using VFO A or VFO B.

2 Press [SCAN].

3 To stop scanning, press [SCAN], or [CLR], or

[SEND], or Mic [PTT].

SCAN HOLD

While using Program Scan, if Menu No. 65

(PG.S.HOLD) is switched ON, then turning the Tuning

or M.CH/VFO.CH control stops the transceiver from

scanning for approximately five seconds. This is also

true if Mic [UP] or [DWN] is pressed. Program Scan

resumes after the five second pause. The default is

OFF.

CONFIRMING START/END LIMITS

1 Recall memory channel 99.

2 Press [DOWN] to check the Start frequency and

press [UP] to check the End frequency.

Jumps to Start

frequency

End Relationship

Start frequency

LOWER THAN

End frequency

Start frequency

EQUAL TO

End frequency

Start frequency

HIGHER THAN

End frequency

Within Scan

range

Lower or higher

than Scan range

Start/End

frequency

Lower or higher

than Start/End

frequency

Within Scan

range

Lower or higher

than Scan range

Jumps to Start

frequency, then

scans up.

Monitors

Start/End

frequency.

Jumps to

Start/End

frequency and

monitors it.

Down

Jumps to Start

frequency, then

scans down.

Start/End

Frequency

Relationship

Current

Frequency

Program Scan

Action

General update of activity

on the entire band or a

sub-section of the band

while in VFO mode.

Quick activity update of all

programmed Conventional

memory channels.

Quick activity update of a

selected group of

Conventional memory

channels.

All-channel

Scan

Group Scan

Memory

Scan

Program Scan

Scan Type Purpose

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood TS-870S Seite 66

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood TS-870S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info