Bedienungsanleitung Kenwood TS-870S (Seite 67 von 104) (Englisch)

606693

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

10 SCAN

MEMORY SCAN

Memory Scan scans all memory channels containing

data (All-channel Scan) or only a group of channels

specified by you (Group Scan). This type of scan

always ascends up through the channel numbers; the

direction of scan cannot be changed. While scanning, if

you want to skip over some programmed channels, turn

the M.CH/VFO.CH control. Pressing Mic [UP] or

[DWN] will also skip over channels but only during

All-channel Scan.

All-channel Scan or Group Scan can be selected via

Menu No. 66 (GRP.SCAN). The default is All-channel

Scan (OFF).

The following are additional important points regarding

the Memory Scan function:

• Starting a transmission by closing the CW key, by

sending a packet, or by triggering the VOX circuit by

voice or the DRU-3 Digital Recording Unit stops

Memory Scan; however, transmission does not

begin immediately.

• Starting the Memory Scan function switches OFF the

RIT and XIT functions. RIT and XIT are not

switched ON again when Memory Scan stops, and

the RIT/XIT offset frequency is not cleared.

•Attempting to use Memory Scan when no data has

been programmed in any memory channels, or

when all channels are locked out, causes an alarm.

Scan will not start.

•To scan channel 99, cancel Memory Channel

Lockout {page 62} for that channel.

Note:

Remember to adjust the squelch threshold level {page 19}

before using Memory Scan.

BUSY FREQUENCY STOP

The transceiver automatically stops Memory scanning

when a signal is detected if Busy Frequency Stop is ON.

The transceiver remains on the same channel for either

a short time or until the signal drops depending on

which Scan Resume method is selected (see below).

The squelch must be adjusted to the noise threshold

point with no signals present for Busy Frequency Stop

to work.

Toggle Busy Frequency Stop OFF or ON via Menu

No. 67 (BSY.STOP). The default is ON.

Note:

Busy Frequency Stop cannot be used with Program Scan.

■ Scan Resume Methods

Scan Resume controls when the transceiver

continues Memory scanning after stopping due to a

busy channel. Neither of the following two modes

function if Menu No. 67 (BSY.STOP) is switched

OFF. These modes cannot be used with Program

Scan.

Time-operated mode: After stopping, Scan checks

the busy channel approximately three seconds later.

If the channel is still busy, Scan waits another three

seconds then resumes scanning. If the channel is

not busy three seconds after stopping, Scan

resumes immediately.

Carrier-operated mode: Scan resumes

approximately two seconds after the signal drops.

Select your preferred Scan Resume method via

Menu No. 68 (CAR.SCAN). The default is

Time-operated (OFF).

ALL-CHANNEL SCAN

The All-channel Scan function scans all memory

channels containing frequency data.

1 Recall a Conventional memory channel.

2 Switch OFF Menu No. 66 (GRP.SCAN).

3 Adjust the SQL control while no signal is present.

• The squelch must be closed before scanning

starts.

4 Press [SCAN] to start scanning.

5 To stop scanning, press [SCAN], or [CLR],

or [SEND], or Mic [PTT].

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood TS-870S Seite 67

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood TS-870S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info