Bedienungsanleitung Kenwood TS-890S (Seite 62 von 196) (Englisch)

683161

Zoom out

Zoom in

Vorherige Seite

1/196

Nächste Seite

Preamplifier

The preamplifier can be configured to one of the two options: low

gain type that places priority on IMD (PRE 1) and high gain type

that places priority on sensitivity (PRE 2).

Press F [ANT/PRE].

Pressing F [ANT/PRE] each time switches the selection in the

following sequence: “PRE 1” → “PRE 2” → “OFF”.

•

The preamplifier selection is stored for each antenna

selection band.

•

The default values are as follows.

Less than 7.5 MHz: OFF

7.5 MHz to less than 21.5 MHz: PRE 1

More than 21.5 MHz: PRE 2

RX Monitor

If weak signals are received while the squelch is closed, the signals

tend to be interrupted. Also, you may sometimes want to monitor

the condition of the RX frequency while in the CTCSS standby

state. In this case, the RX monitor is used to open the squelch

temporarily.

“RX Monitor” (Menu [0-15] to [0-31]) can be assigned to a PF key.

While the PF key that is assigned with “RX Monitor” is pressed and

held down, the squelch opens and the RX frequency can be

monitored. The RX monitor turns OFF once the key is released.

Scanning is paused while PF [RX Monitor] is pressed.

SWL (BCL) Mode

The SWL (BCL) mode is intended for SWL (Short Wave Listening)

and BCL (Broadcast Listening) by displaying the horizontal dial of

the “9R-59” communications receiver on the screen.

1 Press [MENU].

2 Press F [SWL] to display the SWL screen.

•

If F [SWL] is not displayed, press F [MORE].

3 Press [MENU] followed by F [SWL].

Returns to the normal screen.

●

Switching to the SWL mode is not possible while the

transverter is ON.

●

An indicator is not displayed if a memory channel that is

not registered is being called up.

•

Restrictions are applied to the following functions in the SWL

mode.

Function Status

Transmission Disabled

Sending of voice message Disabled

Decoding/Encoding Disabled

Sending of CW message Disabled

TX output power limiter Disabled

Meter switching Disabled

TX filter switching Disabled

Turning ON transverter Disabled

FM tone Disabled

Antenna tuning Disabled

Configuration of the TX

equalizer and related

settings

Disabled

Band Switching in the SWL Mode (VFO Mode)

Press F [BAND

]/ F [BAND ].

•

The “broadcast/meter band” is displayed when the

frequency falls within the band range. The preset broadcast

bands are shown in the table below.

Broadcast/

Meter Band

Lower Limit

[kHz]

Upper Limit

[kHz]

Default [kHz]/ Mode

LW 145 285 145

MW 525 1705 525

120 m 2300 2495 2300

90 m 3200 3400 3200

60 m 4750 5060 4750

49 m 5900 6200 5900

41 m 7200 7450 7200

31 m 9400 9900 9400

25 m 11600 12100 11600

21 m 13570 13870 13570

19 m 15100 15800 15100

16 m 17480 17900 17480

15 m 18900 19020 18900

13 m 21450 21850 21450

11 m 25670 26100 25670

•

The band segments of the SWL mode that is preconfigured on

this transceiver are represented in a slightly different way

compared to conventional meter bands. Different band

segments are used so as to achieve wider coverage to include

the broadcast bands of the different regions and other bands.

5 COMMUNICATING AIDS

5-6

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood TS-890S Seite 62

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood TS-890S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info