Bedienungsanleitung Kenwood TS-890S (Seite 156 von 196) (Englisch)

683161

156

Zoom out

Zoom in

Vorherige Seite

1/196

Nächste Seite

3 Use the function keys, [MULTI/CH] control or USB

keyboard to enter a character string.

Key Behavior

F1 [SPACE] Inserts a space.

F2 [–]/ F3 [+] Selects a character.

F4 [ ]/ F5 [ ]

Moves the cursor.

F [BACK SPACE]

Deletes the character to the left of the

cursor.

F [DEL]

Deletes the character to the right of the

cursor.

F [CHAR]

Switches the type of character to edit.

Pressing the key each time switches the

selection in the following sequence:

ABC (upper case) → !”# (symbols) →

ABC (upper case)

4 Press F6 [SAVE] to save the administrator ID and

password.

•

Each of the ID and password must not be longer than 32

characters.

●

When the KNS Operation is ON, the KNS “Administrator

ID” and “Administrator Password” cannot be edited or

reset.

Built-in VoIP Function

Follow the steps below to configure whether to use the built-in VoIP

function for voice communication between the remote PC and

transceiver during KNS operation.

Set this function to ON (default setting) to use the built-in VoIP

function for voice communication between the remote PC and

transceiver. Set this function to OFF when using ARVP-10 or a

non-KENWOOD VoIP software program.

Select KNS Menu [3] “Built-in VoIP”.

2 Press F4 [SELECT].

3 Press F2 [–]/ F3 [+] to select “On” or “Off”.

Setting Value Off/ On (default)

●

When the setting is changed while a connection is

established (logged in), the new setting will be applied

at the next connection.

●

When using the built-in VoIP, check the following

settings as well. For more details, please refer to the

“TS-890S KENWOOD NETWORK COMMAND

SYSTEM Setting Manual”.

•

Check that the TX operation setting in the modulation

line selection for ARCP-890 matches the audio input

of the modulation line configured on this transceiver.

•

Check that audio input of the modulation line

configured on this transceiver in the “Switching the

Audio Source Input” (8-1) section matches the TX

operation setting selected in the modulation line

selection for ARCP-890.

Audio Input/Output Level of Built-in VoIP

The audio input and output level when using the VoIP can be

adjusted as follows. Use the default setting under normal

circumstances.

Select KNS Menu [4] “Audio Input Level (VoIP)” and

KNS Menu [5] “Audio Output Level (VoIP)”.

2 Press F4 [SELECT].

3 Press F2 [–]/ F3 [+] to select the level.

Setting Value

0 to 50 (default: Menu 4) to 100 (default: Menu

5) (1 step)

Built-in VoIP Jitter Absorption Buffer

Follow the steps below to adjust this item when there is a problem

with the voice quality of VoIP. Selecting a shorter time reduces the

audio delay but noise is more likely to occur due to missing audio

packets or the like. Selecting a longer time increases the audio

delay but noise occurrence due to missing audio packets or the

like is potentially reduced. Set the value as small as possible within

a range that does not affect the operation.

Select KNS Menu [6] “VoIP Jitter Buffer”.

2 Press F4 [SELECT].

3 Press F2 [–]/ F3 [+] to select a jitter absorption time.

Setting Value 80 (default)/ 200/ 500/ 800 [ms]

●

When the setting is changed while the built-in VoIP is in

use, the new setting will be applied the next time VoIP is

used.

Prohibition of Remote Volume Control

This is the function to mute the speaker of the transceiver during

remote operation via KNS.

Use this function during remote operation to stop the audio output

from the speaker of the transceiver.

Select KNS Menu [7] “Speaker Mute”.

2 Press F4 [SELECT].

3 Press F2 [–]/ F3 [+] to select “On” or “Off”.

Setting Value Off (default)/ On

15 NETWORK/KNS OPERATION

15-4

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood TS-890S Seite 156

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood TS-890S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info