Bedienungsanleitung Kenwood VR-715 (Seite 17 von 32) (Englisch)

596380

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

Preparing for surround sound

0 Use the MULTI CONTROL knob or keys to select the appropriate

surround speaker setting.

If you have selected “LRG” as the center speaker setting,

1 SURR NML (normal) : Average size surround speakers are

connected to the receiver.

2 SURR LRG (large) : Large surround speakers are connected

to the receiver.

3 SURR OFF : Surround speaker setting mode to the

receiver is OFF.

• For HTB models, you are advised to select “NML” (normal) for

the surround speakers.

If you have selected other than “LRG” as the center speaker

setting,

1 SURR ON : Surround speaker setting mode to the receiver is

ON.

2 SURR OFF : Surround speaker setting mode to the receiver is

OFF.

! Press the SETUP key again to accept the setting.

• The subwoofer re-mix setting indication “SW RE-MIX” scrolls

across the display.

• If subwoofer is turned OFF, subwoofer re-mix setting is not

visible.

@ Use the MULTI CONTROL knob or keys to select the

appropriate subwoofer re-mix setting.

1 RMX ON : Subwoofer re-mix set mode to the receiver is ON.

2 RMX OFF : Subwoofer re-mix set mode to the receiver is OFF.

# Press the SETUP key to accept the setting.

• The receiver enters the speaker volume level adjustment

mode.

• In step 4 and 5, indications appear only for the selected

channels of the speakers that require adjusting.

Adjust the speaker volume level.

From your usual listening position, adjust the volume levels. The

volume levels from each speaker should be the same.

1 Press the SETUP key to begin TEST TONE.

The selection of AUTO/MANUAL TEST TONE is done by the

MULTI CONTROL knob or keys.

1 AUTO

2 MANUAL

2 Press the SETUP key again to select either AUTO or MANUAL.

Use the MULTI CONTROL knob or keys to adjust the volume

level of the test tone output from the speaker channel to be

adjusted.

For AUTO selection, the test tone is heard from the speakers

in the following sequence for 2 seconds each:

• If you change the volume level settings for the speakers while

listening to music, the settings referred to on this page are also

changed. §

• If any of the speaker is set as OFF during SP SETUP, the TEST

TONE adjustment for the speaker will be skipped.

3 Press the SETUP key.

• The test tone is turned off. The receiver enters the mode for

inputting the distance to the speakers.

4 For MANUAL selection, press the SETUP key each time to

select the speaker channel.

Input the distance to the speakers.

1 Select the DISTANCE from the set up displays and press the

SETUP key again.

2 Measure the distance from the listening position to each of

the speakers.

Jot down the distance to each of the speakers.

Distance to front speakers : ____ feet (meters)

Distance to center speaker : ____ feet (meters)

Distance to surround speakers : ____ feet (meters)

3 Use the MULTI CONTROL knob or keys to select the distance

to the front speakers.

The speaker indicator to be adjusted blinks.

Indication in feet Indication in meters

• The allowable setting range is 1 to 30 feet (0.3m to 9.0m) ,

adjustable in 1 foot (0.3m) increments.

4 Press the SETUP key to accept the settings.

5 Repeat steps 3 and 4 to input the distance for each of the

speakers.

6 Setup is complete when the EXIT indication appears.

• The speakers you have selected should appear on the display.

Confirm that all the speakers have been correctly selected.

7 Press the SETUP key to exit the SETUP mode.

Input level adjustment (analog sources only)

If the input level of an analog source signal is too high, the CLIP indicator

will blink to indicate the source signal. Adjust the input level.

1 Use the INPUT SELECTOR knob to select the source of which the

input level you want to adjust.

• You can store a separate input level for each input source.

2 Press the SOUND key repeatedly until the “INPUT” indication

appears.

3 Use the MULTI CONTROL knob or keys to adjust the input level.

• The input level may be adjusted to any one of three settings: 0dB,

-3dB, and -6dB. (The initial setting is 0dB.)

4 Press the SOUND key again to return to the input indication.

*5337/16-20/EN 27/12/02, 1:05 PM17

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood VR-715 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info