Bedienungsanleitung Kenwood VRS6200 (Seite 18 von 40) (Englisch)

510822

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

Adjust the speaker volume level.

From your usual listening position, adjust the volume levels. The volume

levels from each speaker should be the same.

÷ In steps 5, indications appear only for the selected channels of the

speakers that require adjusting.

1 Press the SETUP key to begin TEST TONE.

2 Use the MULTI CONTROL button (or the MULTI

CONTROL %/ﬁ keys) to select "AUTO" or "MANUAL".

1 "AUTO": Select this setting to adjust the speaker volume

levels using the test tone. The test tone will be output from

every speaker channel in automatic sequence.

2 "MANUAL":Select this setting to select the speaker chan-

nel to output the test tone using the SETUP key.

Press the SETUP key again select either "AUTO" or

"MANUAL".

Use the MULTI CONTROL button (or the MULTI

CONTROL %/ﬁ keys) to adjust the volume level of

the test tone output from the speaker channel to

be adjusted.

For "AUTO" selection, the first test tone is heard from

the front left speaker for 2 seconds. The next test tone

is heard from the speakers in the following sequence

for 2 seconds each.

The channel indication blinks while the test tone is being output.

÷ If you change the volume level settings for the speakers

while listening to music, the settings referred to on this

page are also changed. ¤

÷ When a speaker setup is set to off the volume level for

the corresponding speakers is reset to 0 dB.

For "MANUAL" selection, press the SETUP key each

time to select the speaker channel, and use the MULTI

CONTROL button (or the MULTI CONTROL %/ﬁ keys)

to adjust the volume level.

3 Press the SETUP key to accept the setting.

÷ The test tone is turned off. This model enters the mode

for inputting the distance to the speakers.

Input the distance to the speakers.

This setting allows the signals output from different speakers to reach

the listening position simultaneously.

÷ In steps 6, indications appear only for the selected channels of the

speakers that require adjusting.

Measure the distance from the listening position to each

of the speakers.

Jot down the distance to each of the speakers.

Distance to Front speaker (L) : ____ feet (meters)

Distance to Center speaker (C) : ____ feet (meters)

Distance to Front speaker (R) : ____ feet (meters)

Distance to Surround speaker (RS) : ____ feet (meters)

Distance to Surround back speaker (RB) : ____ feet (meters)

Distance to Surround back speaker (LB) : ____ feet (meters)

Distance to Surround speaker (LS) : ____ feet (meters)

1 Use the MULTI CONTROL button (or the MULTI

CONTROL %/ﬁ keys) to select "DISTANCE" on

setup displays, and press the SETUP key.

2 Use the MULTI CONTROL button (or the MULTI

CONTROL %/ﬁ keys) to adjust the distance to the

front speakers.

The speaker indicator to be adjusted blinks.

÷ The allowable setting range is 1 to 30 feet (0.3 to 9.0 m),

adjustable in 1 foot (0.3 m) increments.

3 Press the SETUP key to accept the setting.

4 Repeat steps 2 and 3 to input the distance for each of

the speakers.

Preparing for playback

Indication in feet Indication in meters

Continued to next page

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood VRS6200 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood VRS6200

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info