Bedienungsanleitung Kenwood VRS6200 (Seite 35 von 40) (Englisch)

510822

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

In case of difficulty

Amplifier

Symptom

Resetting the Microcomputer

The microcomputer may malfunction (unit cannot be operated, or

shows an erroneous display) if the power cord is unplugged while

the power is ON, or due to some other external factor. If this

happens, execute the following procedure to reset the microcom-

puter and return the unit to its normal operating condition.

Unplug the power cord from the wall outlet, then plug it back in

while holding down the ON/STANDBY

key.

÷ Please note that resetting the microcomputer will clear the contents

of the memory and returns the unit to the state it was in when it left

the factory.

Remedy

No sound from the speakers.

Sound is not output from the speaker,

or their sound is very small.

The standby indicator blinks and sound

is not output.

Audio cannot be recorded.

A video source cannot be recorded

normally.

When playing a digital source signal,

the sound is cut off soon after it starts.

Dolby Digital or DTS audio software

cannot be played in multi-channel

audio.

The input for the unit is set automatically

to "GAME" when the unit is turned ON.

÷ Connect them properly referring to "Connecting the speakers". 0

÷ If muting is ON, release it. ™

÷ If headphones are connected, disconnect them. ™

÷ Press the INPUT MODE key to select to full auto mode. 7

÷ Connect them properly referring to "Connecting the speakers". 0

÷ See "Speaker settings" and check if the setting for all of the speakers is correct. ^

÷ Select a surround mode.

÷ Adjust the speaker levels using the test tone. *

÷ Speaker cords are short-circuited. Disconnect the power cord from the AC wall outlet, switch

the receiver OFF, remove the short-circuiting and turn the receiver ON again.

÷ Connect the equipment correctly by referring to "Connecting video components, audio

components" and "Digital connections". 9

÷ If it is the digital audio that you attempt to record, set up the unit correctly by referring to

"Recording music in REC mode". £

÷ Copy-guarded video software cannot be recorded.

÷ There are many possible causes for this problem, depending on the type of player used.

Switch the input mode to DIGITAL MANUAL during playback of the digital source, and restart the

playback from the beginning. 7

÷ Check if the digital output setting of the digital audio player is correct.

÷ The GAME mode function is activated. )

÷ Connect an antenna properly. #

÷ Set the broadcast band properly.

÷ Tune the frequency of the desired station. ¢

÷ Install the outdoor antenna away from the road.

÷ Turn off the power to the appliance.

÷ Install the receiver farther away from the TV.

÷ Preset a station with a receivable frequency.

Radio stations cannot be received.

Interference.

A station which was preset cannot be

received by pressing the corresponding

numeric key.

Tuner

Symptom Remedy

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood VRS6200 Seite 35

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood VRS6200

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info