Bedienungsanleitung Kenwood xd 6000 xh (Seite 70 von 76) (Englisch)

157475

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

XD-8550/XD-6000 (En/T)

Preparation sectionBasic sectionApplication sectionKnowledge sections

÷Adjust the present time again.

÷Adjust the present time referring to “Clock

adjustment”.

÷Set the timer ON time and OFF time.

÷Execute the timer program with the SRS

3D key.

÷Connect antennas.

÷Select a band.

÷Tune to the frequency of the desired sta-

tion.

÷Install the outdoor antenna in an apart posi-

tion from the road.

÷Switch the suspected electric appliance

OFF.

÷Install the TV or the system at an increased

distance between them.

÷Preset stations with tunable frequencies.

÷Preset stations again.

÷This is not malfunction. Press the DEMO

key to cancel the demonstration.

÷Cancel the AUTO POWER SAVE function.

÷Please consult your nearest KENWOOD

service station.

÷There was a power failure.

÷The power cord was unplugged from the

outlet.

÷The present time has not been adjusted or

there was a power failure.

÷The timer ON time and OFF time have not

been set.

÷The timer execution was not set up.

÷The antennas have not been connected.

÷A proper broadcasting band has not been

selected.

÷The frequency of the station to be received

is not tuned.

÷Car ignition noise.

÷Influence of an electric appliance.

÷A TV set is installed near the system.

÷The frequency of the preset station is not

tunable.

÷The preset memory has been cleared be-

cause the power cord has been unplugged

for a long period.

÷The power plug was unplugged from the

outlet while the power switch was ON, or

there was a power failure.

÷The AUTO POWER SAVE function is acti-

vated.

÷There is a certain trouble. The displayed

figure is variable depending on the details of

the trouble.

The clock display blinks without chang-

ing the figures.

Timer operation is not possible.

Radio stations cannot be received.

Noise interferes.

A station has been preset but it cannot

be received by pressing the P.CALL key.

Demonstration starts suddenly.

Power is turned OFF suddenly.

An error message is displayed

(ERROR * (figure))

In case of difficulty

RemedyCauseSymptom

Tuner/Equalizer Unit

‰

⁄

What seems to be a malfunction is not always so. Before calling for service, check the following table according to the

symptom of your trouble.

Operation to reset

The microcomputer may fall into malfunction (impossibility to

operate, erroneous display, etc.) when the power cord is un-

plugged while power is ON or due to an external factor. In this

case, execute the following procedure to reset the microcom-

puter and return it to normal condition.

÷Please note that resetting the microcomputer clears the contents

stored in and returns and to condition when it left the factory.

While holding the ENTER key depressed, unplug the power

cord and plug it again.

ENTER

C-H6 or C-H5

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood xd 6000 xh Seite 70

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info