493359
16
Zoom out
Zoom in
Vorherige Seite
1/34
Nächste Seite
16
zero. When training is started, the programmed values appear and will
count down from the preset value. Values that had not been preset, will
count upwards. If a programmed value reaches the value zero, the dis-
play will flash for five seconds with the originally programmed value and
then will count upwards again. After completing or interrupting the trai-
ning unit the computer will operate as described in section ”Training with-
out preset training data”.
During training, the computer displays whether the preset pulse deviates
from the programmed target value by more than 10 beats/minute. If you
fall below this preset pulse, the symbol ”LO” (12) for ”low” appears; if
you exceed this preset pulse, the symbol ”HI” for ”high” is displayed. The
display "Low" appears for the first time after the programmed pulse value
has been reached.
Training programs 1 - 4 (program mode)
After switching on the computer, press the program key (17) twice. The
computer will be in program mode. The dipslay field (16) will show
"COURSE" and the respective program number. Every pressing of that
key will switch the display to the next training Any time you press the key,
you switch the display further by one training program program (refer to
load profiles on page 22 ). During the first two seconds the program's
complete load profile will be represented in a condensed way for a short
survey. Then, the display will change to the normal representation of the
training program.
No training presets are provided in the stored training programs. How-
ever, there is the possibility to program the pulse limit. For this purpose,
change to the program "COUNT-DOWN" (Training with preset training
data).
For programming the pulse target proceed as described in section "Train-
ing with preset training data.
After programming the pulse value do not press the set key but change to
the desired training program by pressing the program key.
You can regulate the pedalling resistance manually with any stored load
level. The graphic display (5) will adapt itself accordingly (skipping the
25-Watt segment).
When selecting the training program the display will show the appropri-
ate program number and after two seconds the first 15 columns (=12 min-
utes) of the graphic display (5) representing the progress of the course.
The time display will indicate the duration of the course (7), all other val-
ues are set to zero.
If you start pedalling, the time display (7) will start counting down. The
kilojoule and distance covered displays (3 and 9) start counting upwards
while the displays for performance (4), pedal rotations (2) and velocity
(8) show the current values.
If the training unit is interrupted, the selected course will remain where it
has been interrupted. This also applies for energy consumption and dis-
tance covered. If training is taken up again, counting will continue at that
position where it had been interrupted.
Pulse-controlled training
Select the pulse program (program 5) with program key (17). Apart from
the first segment in the lower left column the graphical display of the load
profile is blank. "COURSE" will be displayed as the current mode (6). You
can adjust the preset training values as described under section "Training
with preset training data". The current pulse beat (10) is set to ”– –”
beats/minute. By pressing the "Up" and "Down" keys (15/16) the de-
sired training pulse can be preset. When reaching the desired value you
press the Set key (14) for accepting the value. Afterwards, start pedalling.
The pulse-controlled training will be indicated by a heart symbol appear-
ing in the graphical display every 15 seconds.
The ergometer's computer-controlled eddy-current brake will increase the
pedalling resistance until the preset training pulse is within the admissible
margin of +/- 5 beats/minute.
In the further course of training, keeping the preset pulse frequency will
be automatically controlled.
For an optimal heart frequency control, keeping a preset pedalling rota-
tion margin by the training person is essential. Should the number of ped-
al rotations/minute be outside that margin, the arrow symbols of the dis-
play for exceeding or falling below the admissible pedal rotations (1) will
cause the training person to adapt his/her pedalling velocity.
The geographical representation of the load profile (5) and the other func-
tions are displayed exactly as described in the previous sections.
Information
The ergometer is not depending on the speed. This means that the er-
gometer - independent of an increase or a reduction of the pedalling fre-
quency by the training person - will correctly keep and regulate the
wattages (personally entered or preset by a program) by means of the
electromotive control of the eddy-current brake. The ergometer achieves
the high display accuracy according to DIN EN 957 – 1/5, class A.
Merely the margin of admissible pedal rotations (performance range) de-
scribed before and in the following diagram must be kept for an exact
power indication. The performance range is marked by the arrow sym-
bols (1).
Pulse measuring
The pulse sensor operates with infrared light and measures the changes
of the translucency of your skin resulting from your pulse beat. Before
sticking the pulse sensor to your ear lob firmly rub your ear lob 10 times
in order to increase blood circulation. Because of the required high am-
plification of the input impulses of the pulse sensor disturbing impulses
have to be avoided.
- Therefore carefully stick the ear clip to your ear lob.
- Do not train directly under strong incidence of light, e.g. neon light,
halogen light, spot reflectors, sunlight.
- Avoid vibrations and shaking the ear sensor including cable. Stick the
cable with the clamp to your clothes.
Should there yet be any faulty readings, please once again check the
aforementioned points.
Accessories for pulse measuring
Moreover, there is the possibility to equip the ergometer with a pulse mea-
suring system requiring no cable. The Kettler Cardio-Puls-set consisting of
chest strap, transmitter and receiver permits an ECG-exact pulse measur-
ing. Please ask your specialist trader about this set.
Measuring the recovery pulse
The training computer is equipped with a recovery function which enables
you to measure your recovery pulse at the end of the training.
Press the recovery pulse key (18) at the end of the training. The comput-
er will measure your pulse for one minute. The time will be displayed in
count-down mode. The graphic display (5) is deleted and replaced by the
letters "REC" (”recovery”).
The current recovery pulse is displayed in display field (10).
After completed recovery pulse measurement, a ”fitness mark” with F1 to
F6 will be indicated in the display field (9) for 20 seconds. Afterwards,
the display will switch back to the previous mode. If the recovery pulse
key (18) or the "SET" key is pressed again during measuring, the display
will interrupt the recovery pulse measurement and return to the previous
mode. Should the receipt of the pulse signal be disturbed, the letters ”FE”
(error) will appear in display (9).
Compare your exercise pulse at the end of the training with the recovery
pulse one minute after the end of the training. The computer will calculate
and assess the difference and your ”fitness mark” resulting therefrom ac-
cording to the following formula:
F = 6
(
10 x
P
)
2
P
1
P1 = exercise pulse
P2 = recovery pulse after one minute
P = pulse difference ( P 1
P 2 )
Mark 1 = very good Mark 6 = unsatisfactory
25 50 100 150 200 250 300 350 400
10
20
30
40
50
60
70
80
90
100
110
120
rpm
performance (watt)
Performance Range
16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

kettler-ergometer-cx-1-7987-500

Suche zurücksetzen

  • Wir wollwn die Kurbeln gegen kürzere aaustauschen. Wie kann ich die Kurbeln ausbauen Eingereicht am 22-4-2024 22:43

    Antworten Frage melden
  • Ich kann die wattzahl nicht verstellen, bei Netzbetrieb ganz schwere kurbelbewegung, was kann das sein? Eingereicht am 2-12-2023 12:57

    Antworten Frage melden
  • Wattzahl verändert sich plötzlich und wird viel stärker als angezeigt Eingereicht am 19-3-2023 23:05

    Antworten Frage melden
  • Es geht um die Pflege des Ergometer beziehungsweise Wartung oel nachfühlen Einstellungen und der gleichen Eingereicht am 23-10-2022 15:40

    Antworten Frage melden
  • Mein Ergometer cx1 lässt sich bei eingestecktem Netzteil nicht mehr treten Eingereicht am 1-9-2022 10:43

    Antworten Frage melden
  • Ich rutsche bei jder verstellbaren Möglichkeit vom Sattel herunter. Gibt es noch andere Sattel? Eingereicht am 26-8-2020 19:41

    Antworten Frage melden
  • Beim Einschalten des Ergometers steht die 25 Watt im Display. Die tatsächliche Wattzahl ist gefühlt 10 mal so hoch. Lässt sich nicht einstellen. Die Programme werden zwar angezeigt, jedoch auch mit einem schweren Tritt zu Anfang. Eingereicht am 13-7-2019 08:02

    Antworten Frage melden
  • Die zeitanzeige funktioniert nicht und der Tret-Widerstand bleibt trotz unterschiedlicher Wattzahl gleich gering Eingereicht am 6-2-2019 16:44

    Antworten Frage melden
  • Wie sind die technischen Daten des Netzteils für das Kettler Ergometer CX1 7987-500 Eingereicht am 4-11-2018 18:20

    Antworten Frage melden
  • Hallo wie kann ich die umdrehungsstärke verstellen Eingereicht am 1-11-2018 10:04

    Antworten Frage melden
  • Ich benötige eine Gebrausanleitung für Gerät Kettler Ergometer CX1 7987-500 Eingereicht am 8-10-2018 17:01

    Antworten Frage melden
  • Mein Ergometer lässt sich bei angeschlossenen Netzteil nicht mehr treten Eingereicht am 7-1-2018 18:22

    Antworten Frage melden
  • Wieviel wiegt der Ergometer CX1 von Kettler?
    Vielen Dank für die Antwort Eingereicht am 9-4-2017 09:14

    Antworten Frage melden
  • Ich suche für eine Inbetriebnahme den Gerätestecker für den Trafo Eingereicht am 5-2-2017 10:30

    Antworten Frage melden
  • ich brauche ein Netzteil für Kettler ergometer cx1 oder zumindest die Daten
    Danke. Eingereicht am 5-9-2016 12:01

    Antworten Frage melden
  • An welcher Stelle stecke ich den akkustecker ein Eingereicht am 5-9-2016 10:02

    Antworten Frage melden
  • Pedalarme lösen beim CX1: Schrauben normal im Gegenuhrzeigersinn drehen oder handelt es sich um ein gegenläufiges Gewinde? (Die Schrauben sind völlig "verbockt".) Eingereicht am 14-6-2016 17:41

    Antworten Frage melden
  • Welche kabel brauche ich für Computerverbindung? Eingereicht am 24-1-2016 13:16

    Antworten Frage melden
  • mein netzteil fehlt für meinen ergometer cx 1 7987-500 230v 50hz wenn ich ein netzteil kaufen will wie muss die polarisierung sein Eingereicht am 14-7-2015 13:46

    Antworten Frage melden
  • Das rechte Pedal knackst nach jeder Umdrehung auch spürbar. Was ist zu tun? Eingereicht am 2-2-2015 13:26

    Antworten Frage melden
  • Ich habe ein Kettler Ergometer CX1 seit mehr als 10 Jahren .Leider habe ich nich mehr die 220 Volt Converter. Können Sie bitte mir informieren über die Spezifikationen die Converter oder ist es möglich ein Converter in Schweden zu kaufen oder via Internet von Deutschland?. Leider habe ich kein Antwort von der Schwedishe Generalagent bekommen nach mehr als ein halbes Jahre.


    Mit freundlichen Grüssen

    Finn Waagstein

    Stallviksvägen 11
    42943 Schweden
    email:finn.waagstein@wlab.gu.se Eingereicht am 15-12-2013 17:34

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Kettler Ergometer CX 1 7987-500 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Kettler Ergometer CX 1 7987-500

Kettler Ergometer CX 1 7987-500 Bedienungsanleitung - Deutsch, Englisch, Holländisch, Französisch - 17 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info