Bedienungsanleitung Kitvision Edge HD10 (Seite 10 von 18) (Englisch)

640448

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

18 19

3. Video recording

Manual recording:

Press the “Record” key once in preview mode to start recording. The video recording duration will be displayed at

the bottom right of the TFT display screen, the “Green Indicator of Video/Voice Recording” and the front “Green

Video Recording/Shooting Indicator” will ﬂash slowly, and the recording duration on the LCD segment screen

will be displayed normally. The video recording process will only respond to the zoom function (“–” key). When the

“stop” key is pressed, the system will stop and save the current video recording ﬁle, the front green indicator light

will turn off, the camera will return to the preview state, and the recording duration on the LCD segment screen

will disappear.

Note: If you turn the power off during video recording, the system will save the current ﬁle recorded before

it shuts down

Note: If the battery power is low during video recording, the system will save the current ﬁle recorded and show

the message “Low Battery” on the TFT display screen until the camera is turned off or it automatically enters

standby mode

Note: If the memory space becomes full during video recording, the system will save the current ﬁle recorded,

show the message “Card Full” on the TFT display screen and return to the preview mode. The video recording

duration on the LCD segment screen will also disappear

Note: When the “+” or “–” keys are pressed in voice recording mode, the voice increasing/reducing operation

will not be executed, however when the “+” or “–” keys are pressed when recalling audio ﬁles, the voice

increasing/reducing operation will be executed

[...continued] System parameter setting

8. Factory default: This operation restores the parameter settings to the factory default. If restoring the factory

default, the system will set the time to 01.01.2012

9. Language: Press the “<” or “>” key to choose your desired language

10. Frequency: Select the frequency to 50 Hz or 60 Hz, depending on local grid frequency, in order to avoid the

screen ﬂickering in preview mode or in video recording

11. Date/Time: The time can be adjusted and changed. It will be displayed on the bottom right corner of the video

ﬁle or photo ﬁle when recording or shooting

Note: Press the “M” key in the submenu to exit

Using the camera

1. Insert a micro SD card.

2. Turn the power switch to the “ON” position to turn on the camera. The red indicator will light up and the camera

will enter the preview mode.

Note: If the battery power is low, the battery icon

and the message “Low Power” will be shown on the TFT screen

Note: If no micro SD card is inserted, you will see the micro SD card icon

on the TFT screen

[continued...]

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kitvision Edge HD10 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kitvision Edge HD10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info