Bedienungsanleitung Klipsch LF-10 (Seite 9 von 12) (Englisch)

584802

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

MAIN SPEAKERS FULL RANGE

Connect the subwoofer’s left and right channel “LINE IN” jacks to a non-ﬁltered (full-range) main

channel, pre-amp output on your receiver or pre-amp/processor. Refer to the lefthand side of Figure A.

This signal contains the normal bass information present in the main left and right channels. When

connecting to a component that has only a single pair of pre-amp outputs, “Y” adapters (splitters)

may be used to feed a signal to both the subwoofer and the power ampliﬁer.

Note: When connecting to a mono subwoofer output on your electronics (preferably full range), add

a “Y” cord to the subwoofer end of the cable and connect to both line inputs. This will provide a sig-

niﬁcant increase in the subwoofer’s output level when compared to the connection of just one of the

“LINE IN” inputs.

MAIN SPEAKERS LIMITED RANGE

If a bass limited (high pass ﬁltered) signal is to be sent to your main speakers, connect your main

channel power ampliﬁer inputs to the “LINE OUT” jacks on the subwoofer. Refer to the lefthand

side of Figure B. These outputs will remove frequencies below 50 or 100Hz from your main speakers,

depending upon the setting of the “HIGH PASS SELECT” switch. This type of hookup reduces dis-

tortion and increases the dynamic range of your main ampliﬁer and speakers.

LFE/BYPASS IN (optional)

This input is used with 5.1 (six channel) surround sound systems. The LFE channel contains bass effects

information that is different than the bass signals present in the other channels to enhance the sound-

track’s impact. Connect the “LFE/BYPASS IN” input on the LF-10 and LF-12 to your electronic’s desig-

nated LFE output jack. The “LFE/BYPASS IN” requires a low pass ﬁltered signal from your electronics

(high frequencies removed). Do not connect this input to a full range (unﬁltered) pre-amp output.

Note: The peak level of this signal can be up to 10 decibels louder than main channel bass signals, so

caution should be exercised when connecting to this output and initially adjusting the subwoofer’s

“LFE LEVEL” control. Signals coming into this jack are not affected by the subwoofer’s adjustable

“LOW PASS (Hz)” ﬁlter or main “LEVEL” control. The “LFE/BYPASS IN” will not normally be the

only connection to the subwoofer, unless the LFE channel is the only signal the subwoofer will be

reproducing. The “SPEAKER IN” and “LINE IN” connections are the primary hookups. The “LFE

IN” is compatible with either line level or speaker level connections.

BASS MANAGEMENT

Most surround sound electronics are equipped with a bass management system that permits the selection

of either a full or limited range (bass ﬁltered) operation for each speaker. When using the “LINE IN” or

“SPEAKER IN” connections on the subwoofer, conﬁgure the main channels of your surround electronics

for the “Large” or “Full Range” setting. When connecting to a subwoofer output, defeat the low pass

ﬁltering on your electronics, if possible. If this cannot be done, use the “LFE/BYPASS IN” input and let

your electronics determine the low pass frequency for the subwoofer (the “LFE LEVEL” control now

becomes the primary subwoofer level control). Alternately, you can connect the subwoofer’s “LINE IN”

input to a subwoofer output and set the “LOW PASS (Hz)” control on the subwoofer to a lower cutoff

frequency if desired. Since the speciﬁcs of bass management systems vary from brand to brand, consult

your Klipsch dealer or the manufacturer of your electronics for more details.

Operating Controls

LEVEL

This control adjusts the volume of the subwoofer relative to your main speakers. Use this control to

compensate for room acoustics, subwoofer placement and the sensitivity of your main speakers. This

control affects the signals that are connected to the “LINE IN” or “SPEAKER IN” inputs. It does not

affect the volume level of your main speakers or signals connected to the “LFE/BYPASS IN.”

Suggested control position for initial setup: 10 o’clock.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Klipsch LF-10 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info