Bedienungsanleitung Klipsch RoomGroove (Seite 4 von 20) (Englisch, Französisch, Spanisch)

588332

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

The RoomGroove is designed to allow you to transmit the iPod

or the auxiliary source so that it can be received and played by

other KlipschCast components. To transmit from the RoomGroove,

simply select the source you wish to transmit by pressing the

“Listen” button, or the desired source on the remote (iPod or Aux),

and then press the “Transmit” button. The selected source is now

being transmitted throughout your home and is available to other

KlipschCast-enabled products.

Note: If a RoomGroove is transmitting and a second Room-

Groove is told to transmit, the second RoomGroove will bump

the ﬁrst RoomGroove and occupy that wireless channel. If you

wish to conﬁgure your wireless multi-room system to allow two

RoomGrooves to simultaneously transmit, see the “Transmitting

Audio from Two RoomGrooves” section of this manual.

Transmitting Audio from the RoomGroove

The RoomGroove is designed to allow you to listen to sources

connected to, or integrated into, other KlipschCast components

such as another RoomGroove or the CS-700 DVD Entertainment

System.

To listen to a source being transmitted by another KlipschCast

device, simply press the “Listen” button to access the transmitted

source. The “Listen” light becomes red (or purple for a second

wireless source) when a wireless source is received and played. A

ﬂashing color indicates no source is available on that channel.

Listening to Other KlipschCast Devices with Your

RoomGroove

Blue always indicates a local source. Red and purple indicate

wireless channels. If the color is ﬂashing, the source or wireless

channel is not available.

For systems transmitting from a CS-700 system

and RoomGroove

Local source (iPod or Aux) = blue

Transmitted Cinema System source = red

Transmitted RoomGroove source = purple

For systems transmitting from two RoomGrooves

Local source (iPod or Aux) = blue

1st Transmitted RoomGroove source = red

2nd Transmitted RoomGroove source = purple

Sources and Colors of the “Listen” Light

In systems not incorporating a CS-700 system (or if the cinema

system in not intended to be part of the wireless multi-room

system), two RoomGrooves can transmit simultaneously. To enable

this feature, all components of the wireless multi-room system

must be assigned to a home code from 5 to 9. Selecting a home

code from 5 to 9 will allow a second RoomGroove to occupy the

wireless channel which was previously assigned to the CS-700.

(See “Setting the Home Code” for more detailed information.)

If two RoomGrooves are transmitting and you wish to transmit

from a third and control which wireless channel will be used for the

new transmission, you must ﬁrst select the broadcast you wish to

terminate by pressing the “Listen” button until that source is heard.

Then press transmit and the new source will occupy that wireless

channel and stop the transmission of the other source. You should

now hear the new source in all the locations in which the previous

source was playing. The new source should now be available to all

active listeners.

Note: All devices in the wireless multi-room system must be set

to the same home code in order for transmissions to take place.

Transmitting Audio from Two RoomGrooves

The home code dial on the rear of your RoomGroove allows you

to select a code speciﬁc to all of your KlipschCast components

to avoid interference from neighboring systems. The home code

numbers range from 0 to 9 with 0 set as the default. All of your

KlipschCast components will initially be set to 0 and allow one

wireless channel to broadcast audio from a cinema system and

the second wireless channel to broadcast wireless audio from a

RoomGroove. The home code number should only be changed for

one of two reasons:

1) There is interference from a neighboring system – If a

neighboring system in interfering with your wireless system,

simply change all KlipschCast components to another home code.

KlipschCast components will only transmit and receive audio from

components on the same home code. Home codes 0 through 4

can be used for systems transmitting audio from a cinema system

and a RoomGroove (home codes 5 through 9 are reserved for

systems transmitting from two separate RoomGrooves and no

cinema system).

2) You wish to transmit audio from two RoomGrooves (not a

cinema system) – If you wish to transmit audio from two separate

RoomGrooves and not a cinema system, simply choose a home

code from 5 to 9 and change all KlipschCast components to that

home code. KlipschCast components will only transmit and receive

audio from components on the same home code.

Once the home code has been changed, you must disconnect and

reconnect the power cord from the wall outlet for the change to be

made. This will change the home code and allow the component to

talk to other KlipschCast components set to the same home code.

Setting the Home Code

Transmitting Audio from the CS-700

In a multi-room system incorporating a CS-700 cinema system

(sold separately), the RoomGroove remote can be used to directly

select sources from the CS-700 once the CS-700 has been

selected by the RoomGroove’s “Listen” button. The CS-700

will default to transmit its local source (the source selected for

listening/viewing on the CS-700 system) until another source is

selected. See the “Remote Control” section of this manual for

details on the remote’s functionality.

Note: All devices in the wireless multi-room system must be set

to the same home code in order for transmissions to take place.

Klipsch RoomGroove Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info