Bedienungsanleitung Kodak i1860 (Seite 104 von 108) (Englisch)

212708

104

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

6-12 A-61555 April 2009

Problem solving Use the chart below as a guide to check possible solutions to problems

you may encounter when using the Kodak i1800 Series Scanners.

Problem Possible Solution

Scanner does not power on Make sure that:

• the power cord is plugged securely into the receptacle in the back of

the scanner.

• the wall outlet is not defective (call a licensed electrician).

• both power switches are on (the main breaker switch on the back of the

scanner and the power switch located on the side of the scanner).

Scanner is not being recognized by the

Scan Validation Tool

Make sure that:

• when the software was installed, it was installed by someone with

Administrator privileges.

• the FireWire cable is plugged in securely.

• the scanner shows up in the Device Manager as an “imaging” device.

• you cycle power on the scanner and PC. First cycle power to the PC.

Then make sure the FireWire cable is securely fastened, then restart

the scanner.

The scanner will not scan/feed

documents

Make sure that:

• the power cord is plugged in and the power is on.

• the pod is completely closed.

• the scanner is enabled from the host.

• documents are making contact with the feed module.

• for documents that require special handling, press the gap release

button during feeding.

• the documents meet specifications for size, weight, etc.

• if you are feeding small documents, be sure that the documents are

covering the paper present sensor in the input elevator.

• you check the feed module, separation roller, and pre-separation pad

for signs of wear and replace these parts if necessary.

• a very dark document or curled document is not on the bottom of the

stack. Place a white sheet of paper at the bottom of the stack and scan

again.

• use Count Only mode to test feeding.

Side guides will not move Remove all documents from the input elevator and be sure the locking

switch is in the unlocked position.

More than one document is entering the

transport at one time

too many multifeeds are being detected

Make sure that:

• the guidelines for document preparation have been followed (e.g.,

staples, paper clips are removed; lead edges are aligned, etc.)

• documents meet specifications for size and weight.

• the multifeed sensors are clean.

• the separation roller, feed module, and pre-separation pad are clean

and properly installed.

• you have checked the feed module tires, separation roller tires and pre-

separation pad for signs of wear and replaced as needed.

• ultrasonics have been calibrated.

Image quality is poor or has decreased Make sure that:

• the imaging guides are clean. See Chapter 5, Maintenance.

• the scanner has been calibrated. See Chapter 3, “Calibrating the

scanner”.

• if using iThresholding, reduce the Contrast value.

• try a different color table.

• for color or grayscale images, consider creating a custom color table

using the Brightness and Contrast Control utility.

If unsatisfactory image quality persists, call Service.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kodak i1860 Seite 104

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kodak i1860

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info