Bedienungsanleitung Kodak i1860 (Seite 105 von 108) (Englisch)

212708

105

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

A-61555 April 2009 6-13

Problem Possible Solution

Calibration has failed Make sure that:

• you are using the proper calibration target and it is oriented correctly for

the type of calibration you are performing. The Image calibration target

and Ultrasonics calibration target are different.

• the imaging guides are clean.

• the transport is clear of obstructions.

• the sensors are clean.

• the calibration target you are using is clean.

If unsatisfactory image quality persists, call Service.

Documents are jamming Make sure that:

• the guidelines for document preparation have been followed (e.g.,

staples, paper clips are removed; lead edges are aligned, etc.)

• the output tray and side guides are adjusted for the length and width of

the documents being scanned.

• all jammed documents have been removed from the transport area.

• documents meet specifications for size and weight.

• the sensors are clean.

• the separation roller, feed module, and pre-separation pad are clean

and properly installed.

• the transport rollers are clean.

• the background strips are properly installed.

• you have checked the feed module tires, separation roller tires and pre-

separation pad for signs of wear and replaced as needed.

Long documents are not feeding or are

jamming

Make sure that:

• the input elevator extender is pulled out to provide support for long

documents.

• the output tray is adjusted for the length of the documents being

scanned.

• the output tray is installed properly.

• document extenders are installed correctly.

Roller marks appear on the documents

after scanning

Clean the feed module tires, separation roller tires and transport rollers.

Vertical streaks appear on the image Make sure that:

• imaging guides are clean.

• the scanner was thoroughly cleaned before the last image calibration.

• when you calibrate the scanner that you are using a good, clean

calibration target. Use the calibration target provided with your scanner.

•

If you are using iThresholding, reduce the Contrast value.

The Enhanced Printer is not printing as

desired

If you are having problems printing on scanned documents:

• verify that the ink cartridge is not empty.

• be sure the ink cartridge is properly installed.

• be sure the ink cartridge is located in the correct position for printing.

• make sure that the printer carrier is properly seated in its slot.

• verify that all printer connectors are securely fastened and that the

ribbon cable is securely attached.

• verify that the printer has been enabled through the host and that the

expected print string has been specified.

Image too small or has a black border

• Clean the imaging guides. See Chapter 5, Maintenance.

• Clean the scanner. See Chapter 5, Maintenance.

• If using iThresholding, reduce the Contrast value.

• Check for scratches on the black (or white) background strips. Replace

if necessary.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kodak i1860 Seite 105

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kodak i1860

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info