Bedienungsanleitung Kona 2013 (Seite 19 von 42) (Englisch)

780528

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite

KONA OWNER’S MANUAL

one, should be on rider’s left side of the bicycle (g. 8a

& b). If your bike has a clip-on type secondary retention

device, engage it.

(3) If you have a traditional cam action mechanism:

holding the cam lever in the ADJUST position with your

right hand, tighten the tension adjusting nut with your

left hand until it is nger tight against the fork dropout

(g. 8a). If you have a cam-and-cup system: the nut and

cup (g. 8b) will have snapped into the recessed area of

the fork dropouts and no adjustment should be required.

(4) While pushing the wheel rmly to the top of the slots

in the fork dropouts, and at the same time centering the

wheel rim in the fork:

(a) With a cam action system, move the cam lever up-

wards and swing it into the CLOSED position (g. 8a & b).

The lever should now be parallel to the fork blade and

curved toward the wheel. To apply enough clamping force,

you should have to wrap your ngers around the fork blade

for leverage, and the lever should leave a clear imprint in

the palm of your hand.

(b) With a through-bolt or bolt-on system, tighten the

fasteners to the torque specications in the hub manufac-

turer’s instructions.

NOTE: If, on a traditional cam action system, the lever

cannot be pushed all the way to a position parallel to

the fork blade, return the lever to the OPEN position.

Then turn the tension adjusting nut counterclockwise

one-quarter turn and try tightening the lever again.

(5) With a through-bolt or bolt-on system, tighten the

fasteners to the torque specications in the hub manufac-

turer’s instructions.

WARNING: Securely clamping the wheel with a

cam action retention device takes considerable force.

If you can fully close the cam lever without wrapping

your ngers around the fork blade for leverage, the

lever does not leave a clear imprint in the palm of your

hand, and the serrations on the wheel fastener do not

emboss the surfaces of the dropouts, the tension is

insufcient. Open the lever; turn the tension adjusting

nut clockwise a quarter turn; then try again. See also

the rst WARNING in this Section, p. 16.

(6) If you disengaged the brake quick-release mechanism

in 3. a. (1) above, re-engage it to restore correct brake

pad-to-rim clearance.

(7)

Spin the wheel to make sure that it is centered in the

frame and clears the brake pads; then squeeze the brake

lever and make sure that the brakes are operating correctly.

c. Removing a disk brake or rim brake Rear Wheel

(1) If you have a multi-speed bike with a derailleur gear

system: shift the rear derailleur to high gear (the small-

est, outermost rear sprocket).

If you have an internal gear rear hub, consult your dealer

or the hub manufacturer’s instructions before attempting

to remove the rear wheel.

If you have a single-speed bike with rim or disk brake, go

to step (4) below.

(2) If your bike has rim brakes, disengage the brake’s

quick-release mechanism to increase the clearance be-

tween the wheel rim and the brake pads (see Section 4.C,

gs. 11 through 15).

(3) On a derailleur gear system, pull the derailleur body

back with your right hand.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kona 2013 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info