Bedienungsanleitung Korg AX100G (Seite 9 von 18) (Englisch)

488491

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

3. Editing

In Program mode and Effect Select mode, you can

edit each effect, adjust the noise reduction and pro-

gram level, and modify the program name.

During editing, the edit icons in the multi-display

and the LEDs beside the select switches for each ef-

fect will blink.

If you wish to save the effects you edited, you must use the "Pro-

gram Write" operation. If you turn off the power or switch to

another effect without performing "Program Write," the previ-

ous settings will reappear.

Edit icon

Value of the parameter

The parameter assigned

to the knob you moved

Editing the effects

The drive amp effect can be edited immediately by turning the

value knobs or type knob; you do not have to press the

DRIVE·AMP switch. (Refer to the section below, "Drive Amp

effect Quick Edit function.")

To edit other effects, press the corresponding select switch to put

that effect in Edit mode (the LED will blink).

Drive Amp effect Quick Edit function

You can edit the Drive Amp effect (unless the effect is turned off)

by using the Type knob to re-select the effect, or by rotating the

five value knobs to modify the parameter values. When you do

so, the multi-display will show the effect name or parameter name

assigned to the corresponding knob, and its current value.

Even when another effect such as Modulation or Pedal is in edit

mode, you can still turn the type knob to edit the drive amp ef-

fect.

Editing is not possible if other functions are assigned to the value

knobs, nor in Bypass, Mute, or Phrase Trainer modes.

Drive amp channel

For each program, the Drive Amp effect has settings for two chan-

nels, A and B.

Press the DRIVE·AMP switch located at the right of the panel to

select the channel you will edit. Each time you press the switch,

the LED will change between green (channel A) and red (chan-

nel B).

Editing the Drive Amp effect (example)

As an example, here's how to set channel B of the Drive Amp

effect to TUBE OD.

1. Press the DRIVE·AMP switch several times to select channel

B (red LED).

If the multi-display reads "TUBE OD," no change is necessary.

Otherwise, rotate the Type knob to select TUBE OD. If the Type

knob is already located at the TUBE OD position, turn it first

to another effect type, and then turn it back to TUBE OD.

3. The multi-display will indicate "TUBE OD" as the effect name.

If you selected the effect that had been programmed, the Origi-

nal icon in the multi-display will light.

4. The five value knobs will be assigned to GAIN, TREBLE,

MIDDLE, BASS, and LEVEL respectively, and will adjust the

value of the corresponding parameter. (See p.12, "Effect pa-

rameters.")

5. As you rotate the knobs, the sound will change and the multi-

display will show the parameter name assigned to that knob

and the current value. If you rotate the knob to adjust the value

to the value it had before you began editing the original pa-

rameter value icon in the multi-display will light.

Original icon

Value of the parameter

Parameter

DRIVE·AMP

switch

Channel A/B display

If you do not wish to use the Drive Amp effect, use the Type

knob to select OFF so that the Drive Amp effect will be bypassed,

and the multi-display will indicate "DRV OFF." In this case, the

LED beside the DRIVE·AMP switch will go dark.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Korg AX100G Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info