Bedienungsanleitung Korg Kross 2 (Seite 28 von 152) (Englisch)

707348

Zoom out

Zoom in

Vorherige Seite

1/152

Nächste Seite

Setup

3. Connect a dynamic mic to the MIC IN jack.

Note: This jack does not support condenser mics or other

mics that require phantom power or plug-in power. Such

types of mic must be connected via a mic amp.

Connecting a guitar

Connect your guitar to the MIC IN jack. Please see the

“Connecting a mic” section above.

Note: Most guitars and basses (i.e., equipped with passive

pickups that do not have a preamp) produce a low output

level that cannot be recorded at a satisfactory volume or

quality. Route such instruments through a preamp or effect

unit before connecting them to the KROSS. If the output of

the preamp or effect unit is too high, and you cannot set an

appropriate input level, adjust the output level of the preamp

or effect unit. If your instrument has active-type pickups

with a built-in preamp, simply connect it directly.

Connecting an audio player

An audio player or other stereo line input source can be

connected to the LINE IN jack.

1. Make sure that the SWITCH button LED (ON/OFF)

is off (unlit) in the AUDIO IN 1 row of the

REALTIME CONTROLS section.

2. Turn the VOLUME knob of the KROSS all the way to

the left, minimizing the volume.

3. Connect your audio player to the LINE IN jack.

Selecting the audio input

Specify and enable the audio input to which you connected

your mic, guitar, or audio player as described above.

Note: It's not possible to input audio via both the LINE IN

jack and MIC IN jack simultaneously.

1. In REALTIME CONTROLS, use the SELECT button

to select AUDIO IN 2.

2. In REALTIME CONTROL, use the SWITCH button

to select either MIC (LED lit) or LINE (LED unlit).

Only the selected input is enabled.

Adjusting the audio input

1. Select the input. (“Selecting the audio input” on

page 22)

2. Use the GAIN to adjust the level of the external audio

signal. In REALTIME CONTROLS, use the SELECT

button to select AUDIO IN 1, and use the KNOB 1

knob to adjust the volume of the input signal.

So that the sound does not change suddenly while

you're performing, the GAIN value does not change

until the position of the knob matches the current

value. Once you have turned the knob to the position

of the current value, you can adjust the value.

3. If you want to change the amount of effect that is

applied, adjust MFX2/REVERB in the AUDIO IN 1

row of the REALTIME CONTROLS section.

Operating the KNOB 2 knob adjusts the amount that

is sent to the MFX2 effect.

Tip: Although it will depend on the settings of the

program or combination, Send2 typically applies reverb.

For more about effect-related settings, see “Effect

settings for audio input” on page 71.

4. To specify the pan, or the amount that is sent to the

MFX1 effect, adjust settings in the AUDIO IN -

QUICK SETTING- dialog box. If you press the

FUNCTION button while the popup screen is shown

during steps 2 and 3, the AUDIO IN -QUICK

SETTING- dialog box appears.

Note: The Global setting (G-SET) dialog box is shown

above. These input settings are used by the entire

KROSS. (see “Global audio input settings (G-SET) and

individual settings”)

5. By setting the Direct Send parameter, you can record

just the external audio input from a mic connected to

the MIC IN jack, without recording the sound of the

KROSS's performance. For example if you're

rehearsing in the studio, you could record only the

band's performance while you play the KROSS.

Direct Send off: The audio input and the KROSS's

performance are mixed and recorded.

Direct Send on: Only the audio input is recorded. The

sound of the KROSS's performance is not mixed. (In this

case, the audio input sound is not output from audio out.)

6. To save the settings, press the PAGE+ (WRITE G-

SET) button. A dialog box will appear; press the

MENU (OK) button to save the settings.

Note: The explanation above is the procedure for saving

Global settings (G-SET). (see “Global audio input

settings (G-SET) and individual settings”)

7. Press the MENU (DONE) button to return to the page

you were in prior to the dialog box.

Global audio input settings (G-SET) and individual

settings

The audio input of the KROSS is affected by settings that are

shared by the entire instrument (Global settings / G-SET)

and by individual settings that are made independently for

each program, combination, or MIDI song.

With the factory settings, the programs, combinations, and

MIDI songs are set to use G-SET by default. For some

sounds, individual settings have been made for the vocoder

sound or vocal effect. By opening the AUDIO IN -QUICK

SETTING- dialog box, you can check whether that program

or combination uses the global settings (G-SET) or its own

individual settings.

Tip: Sounds with individual settings are stored in the

DRUM/SFX category.

Direct Send

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Korg Kross 2 Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Korg Kross 2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info