Bedienungsanleitung Korg Kross 2 (Seite 85 von 152) (Englisch)

707348

Zoom out

Zoom in

Vorherige Seite

1/152

Nächste Seite

Creating a user arpeggio pattern Editing a user arpeggio pattern

An example of creating a pattern

1. Access the ARP PATTERN> EDIT page.

2. Enter the tones shown in the following illustration.

3. When you play the keyboard as shown in the

illustration, the arpeggiator will begin playing.

Tone 0 corresponds to the pitch of the lowest key of the

chord you play on the keyboard. (If Sort is unchecked, it

will correspond to the pitch of the first note you play.)

4. For steps 01–08, adjust settings for “Pitch (Pitch

Offset),” “Gate,” “Vel (Velocity),” and “Flam.”

Pitch (Pitch Offset): This offsets the pitch of the

arpeggio note in semitones up or down. You can input the

same tone for each step, and change the Pitch Offset

value for each to create a melody using a single tone. (see

“Melody pattern”)

Gate: Specifies the length of the arpeggio note for each

step. With a setting of LGT (Legato), the note will

continue sounding either until the next note of the same

tone or until the end of the pattern. With a setting of Off,

the note will not sound.

Vel (Velocity): This specifies the strength of the note.

With a setting of Key, the note will sound at the strength

of how it was actually played.

The Gate and Veloc ity settings you select here will be

valid if the Gate and Velo city parameters (P-ARP>

SETUP page) of the program that was selected in

Program mode are set to Step. If these parameters have

a setting other than Step, the Gate and Velocity settings

that were specified for each individual step will be

ignored, and all notes of the arpeggio will sound

according to the settings in P-ARP> SETUP page. Be

sure to verify the settings of the program.

When specifying Gate, Velocity, and Swing, set the

PROG> ARP page parameters [GATE], [VEL], and

[SWING] to +00.

5. To rename the user arpeggio pattern, use the Rename

Arpeggio Pattern function. (“Rename Arpeggio

Pattern” on page 179 of the Parameter Guide)

6. Be sure to execute the Write operation if you want the

edited user arpeggio pattern to be saved in internal

memory. (→ p.124)

If you turn off the power without writing, the edited

content is lost.

7. If you want to save the state of the program at the

same time, return to program mode and write the

program. (→ p.122)

Melody pattern

1. Access the ARP PATTERN> EDIT page.

2. Specify tone 0 for Step 01, 02, 03, 04, 05, 07, 08 (all

other than 06).

3. Specify the pitch. Set the “Step” 02 “Pitch” to +10,

“Step” 05 “Pitch” to +12, and the “Step” 08 “Pitch” to

–2.

4. Play a single key; the arpeggio will begin playing.

Chordal pattern

1. Access the ARP PATTERN> EDIT page.

2. In Step 01, set tone 01.

3. In “Step” 03, 04, 06, and 08, set tones 00–04.

4. Select “Step” 01, and set “Gate” to LGT (Legato).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Korg Kross 2 Seite 85

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Korg Kross 2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info