Bedienungsanleitung Korg microKORG S (Seite 10 von 73) (Englisch)

707422

Zoom out

Zoom in

Vorherige Seite

1/73

Nächste Seite

Turning the power on

2. Turning the microKORG S on

Before you turn the microKORG S on, you should lower the level of your

monitor system or other connected output device.

Turn the microKORG S's VOLUME knob all the way toward the left.

Hold down the power switch until the display lights up.

The display will indicate the program number.

Turn the microKORG S's VOLUME knob toward the right to an appropriate

position.

Adjust the volume of your external output device.

21, 3

3. Turning the microKORG S off

After saving any necessary data (such as a program you have edited) turn the

instrument off using the reverse order of the power-on procedure.

The Auto Power-Off Function

The auto power-off function automatically turns off the microKORG S if it is not

played or operated* for a set period of time. The factory default setting is 4 hours.

* Turning the [VOLUME] knob is not considered an operation.

(➝ Quick Start Guide)

1. The power supply

Before you connect the power supply, make sure that the power switch is turned off

(i.e., that the display and switches are unlit).

Connecting the AC adaptor

Firmly insert the plug of the included AC adaptor into the jack. Then connect the

AC adaptor to an AC outlet.

Never use any AC adaptor other than the included one.

Inserting/exchanging batteries

The microKORG S can also be operated on batteries.

Batteries are not included. You will need to purchase them

separately.

Make sure that the power switch on the microKORG S is turned

off. Then open the battery cover located on the bottom of the case.

Insert six AA alkaline batteries.

Be careful to observe the correct polarity of the batteries.

Close the battery cover.

When the microKORG S is used with batteries, the speaker output level will be

lower than when the AC adapter is used. In addition, the output level will

gradually decrease as the battery power level diminishes.

Low battery display “ ”

When the batteries run low, the display will indicate " ," and the "." at the far

right will begin blinking. If you continue using the microKORG S, the Protect

setting will be turned on automatically, and you will be unable to edit program or

global settings. We recommend that you install new batteries or switch to the AC

adaptor as soon as possible. If this state occurs while you are editing, and you want

to save your settings, connect the AC adaptor and execute the Write operation.

You can cancel the "

" display by pressing the SHIFT key.

Batteries that have become unusable should be removed from the microKORG

S as soon as possible. Leaving such batteries installed may cause malfunctions

(due to battery leakage, etc.). You should also remove the batteries if you will

not be using the microKORG S for an extended period of time.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Korg microKORG S Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Korg microKORG S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info