Bedienungsanleitung Kratki MBZ (Seite 14 von 136) (Deutsch, Englisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch)

813969

Zoom out

Zoom in

Vorherige Seite

1/136

Nächste Seite

Preparation for installation

The replace insert is delivered ready to be built and installed. After unpacking, check the complete-

ness of the unit and make sure that the kit components have not been damaged during transport. In

selected replace inserts, the deector, handle, air damper handle and the rod handle used to adjust

the ue gas damper (shaft) should be installed.

In guillotine-type inserts, the screws locking the counterweight should additionally be removed. De-

pending on the model, check:

- the mechanism for adjusting the chimney draught (shaft),

- the mechanism for adjusting the air supply to the combustion chamber (ash drawer, air damper),

- the mechanism of operation of the front door closure (guides, hinges, handle),

- correctness of installation of ash pan/ash drawer and grate,

- the condition of the glass and the sealing cord of the re door,

- the condition of the ceramic lining of the rebox (selected replace inserts).

The inspection should be carried out in the presence of the installer. If you nd any damage or decien-

cies, please contact customer service. Before installing the replace insert, the chimney ue must be

expertly inspected and received for its technical parameters and condition - tightness, patency. Instal-

lation of the replace stove can be carried out after a positive result of the chimney sweep’s expertise

of the ue, and after checking the completeness of the device and the proper operation of all the

mechanisms mentioned above.

Location of the replace insert and connection to the chimney

The replace insert must be installed on a noncombustible oor with a minimum thickness of 30 cm,

and the oor at the replace door must be protected by a strip of noncombustible material with a

minimum width of 50 cm. The safe distance of combustible elements from the glass should be min.

150 cm (Fig. 1 b). Before installing the replace, it is also necessary to check the mechanical strength

of the oor on which the replace insert is to be placed, taking into account the total weight of the

insert and its housing.

The device should be located as close as possible to the ue pipe. When moving the replace, do not

grab the handle, as you risk damaging it. The appliance must be placed at a safe distance from any

ammable products. The ue under which the replace is connected should be airtight, smooth and

made of low heat-conducting materials. The connection between the chimney and the replace stove

must be made of non-ammable materials protected against oxidation (enamel or steel ue pipe).

Connection to a common chimney is possible.

When connecting to a common chimney, the door must always be closed. The pressure of the chimney

should be 12 Pa.

A diagram of an example installation and connection to the chimney is shown in Figure 1 a) ( 1 - -

replace insert, 2 - interior of the housing, 3 - decompression chamber , 4 - outdoor air intake duct,

5 - outdoor air intake, 6 - chimney, 7 - connector, 8 - ventilation grille, outlet, 9 - ventilation grille, inlet,

10 - layer of non-combustible material).

The appliance should be connected under a chimney section that provides a draught of 12 +- 2 Pa. If

the chimney produces a weak draught, consider laying new ues. It is also important that the chim-

ney does not produce excessive draught, in which case a draught stabilizer should be installed in the

chimney. Alternatively, special chimney endings equipped with an exhaust fan that regulates draught,

or other chimney attachments (e.g. a reman) may be used. Have your chimney ue inspected by a

master chimney sweep.

The room in which the device will be installed must have a volume resulting from the ratio of 4 m 3 x

1 kW of nominal thermal power of the device, but not less than 30 m3. In addition, it should have an

ecient ventilation system and provide the necessary amount of air required for the proper operation

of the cartridge. It is assumed that to burn 1 kg of wood in a replace with a closed combustion cham-

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kratki MBZ Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info