Bedienungsanleitung Kratki MBZ (Seite 16 von 136) (Deutsch, Englisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch)

813969

Zoom out

Zoom in

Vorherige Seite

1/136

Nächste Seite

department of Kratki.pl Marek Bal.

Note

A burning replace insert is hot. During all handling and operation of the replace stove, be aware that

the elements of the replace stove may be hot, so protective gloves should be used for handling. Do

not leave ammable materials in the vicinity of the replace, or extinguish the re in the rebox with

water, or operate the replace with a broken glass.

The safe distance of combustible elements from the glass is min. 1,5 m. Staying near

working appliance, children or other unaware persons should not be left unattended. If the replace

stove is equipped with a grate and an ash pan, do not operate the unit without these elements.

First launch

The replace insert should be started up for the rst time by a certied installer. Before ring up, remo-

ve any decals from the surface of the glass, and the sponge protecting the rebox lining. The rst few

kindlings should be made before the casing is made to check the operation of all controls and other

moving parts of the insert.

During the rst ring, the phenomenon of hardening of the paint occurs, accompanied by a charac-

teristic odor and emission of smoke on the surface of the insert. The rst few times the replace stove

is used, it may also smell of enamel, silicone sealant and other materials used in construction. This is

normal, but will disappear after a few smokes. The rst burning in the insert should be carried out in

a well-ventilated room. During the rst two weeks of use, a newly installed replace insert should be

operated at about 30% of its rated power, gradually increasing the temperature. This way of operating

the insert allows for the gradual removal of internal stresses, which prevents the formation of thermal

shocks. This has a very strong inuence on the cartridge’s subsequent durability.

Firing up in a replace insert

The only correct and recommended way to light replaces is the so-called re from above. To light

the re in the replace insert, open all the dampers and air dampers and then use the handle to open

the door of the insert. First, in the central part of the rebox, alternating billets (no more than three

layers with a diameter of about 10 - 13 cm) are placed. On top of the billets are placed smaller logs

(diameter of about 2 - 5 cm) in such a way as to ensure free air ow between them. At the very top,

a re starter should be placed. It is forbidden to use for kindling materials other than those provided

in the instruction manual. It is forbidden to use ammable chemical products for kindling, such as oil,

gasoline, solvents and others.

Light the kindling and close the door. Kindling may take several to several minutes. If there is insu-

cient draught in the chimney, unseal the replace door at the initial stage of kindling by swinging it

open. If the replace insert is not equipped with an air intake from the outside, it is good practice to

open the window in the room where the appliance is located. The method of opening and closing the

door on replace inserts is shown in Fig. 2. a) and b) replace inserts with doors that open to the side,

c) and d) replace inserts with doors that lift upwards (unlock the lock(s) before opening).

Fuel replenishment and combustion control

After lighting the re, wait for a layer of embers to form, and then ll the rebox of the insert with

wood, arranging the fuel in a way that will reasonably ll its hearth. The loading weight should be cal-

culated based on the power of the insert. It is assumed that 1 kg of wood with a moisture content of up

to 20% yields 3 kW of power. When relling the fuel, follow the rule that opening the front door should

be done slowly while opening the shaft, if the insert is equipped with it. After ring up the relled fuel,

close the air damper so that the combustion process does not proceed too rapidly. Before closing the

air damper, make sure that the fuel burns intensely enough that reducing the air supply will not extin-

guish the re. If the replace stove is equipped with a vent, it should be closed during this phase of

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kratki MBZ Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info