Bedienungsanleitung Kress 1500 KS (Seite 10 von 56) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

508050

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

10 English 1500 KS

Cutting Angle Adjustment

The base 13 can be tilted up to 45° for bevel cuts.

First loosen the two clamp levers 8 on the angle

scales incline the base according to the scale and

then retighten the clamp levers 8.

There are markings for 0, 15, 30 and 45° on the rec-

tangular opening at the front of the base. These mark-

ings show where the middle of the cut line is for bevel

work (the middle position has changed due to the

base having been tilted).

Note: For mitre cuts, the cutting depth does not corre-

spond to the value indicated on the cutting depth

scale 19.

The base has been set in the factory so that it makes

an angle of exactly 90° with the blade in basic position

(zero mark on scale). If you discover a slight deviation,

it can be corrected by turning the two threaded

studs 20 slightly.

Parallel Guide

The parallel guide 11 makes possible exact cuts

along a workpiece edge or the cutting of parallel

strips.

Release star grip bolt 10, slide parallel stop 11 by the

required amount. Tighten up star grip bolt 10.

Check before putting into operation that the mains

voltage agrees with the voltage specified on the

nameplate of the machine.

Switching on and off

Switching on: Press the safety button 2.

Press the on-off switch 3 and hold depressed.

Note: The on-off switch 3 cannot be locked on.

Switching off: Release the on-off switch 3.

Before any work on the machine itself, pull the

mains plug!

Wear protective gloves.

The saw blades used must conform with the char-

acteristic data given in these operating instructions.

Press and hold down the pin for spindle lock 4 and if

necessary rotate the blade until the lock snaps into

place.

Removal:

Swing back and hold the swinging protective

guard 12. Unscrew the clamping screw 22 with the

Allen key 21.

Remove the clamping flange 23 and the saw blade.

Assembly:

Clean the motor spindle, saw blade and all clamping

parts to be mounted. Mount the clamping screw 22

with washer and the clamping flange 23. Tighten with

the Allen key 21.

Pay attention to the correct mounting position of

the mounting flange 24 and the clamping

flange 23.

Observe when assembling: The cutting direction of

the teeth (direction of arrow on the saw blade) and

the direction of rotation arrow on the protective

guard must agree.

The swing guard 12, which covers the blade, moving

back automatically when the blade is brought into the

work, at the same rate at which the saw is brought in.

When you reach the end of the cut, the swing guard

moves back by spring action to cover the blade again.

The eye shield 14 allows you to look directly at the cut

or layout line. It adjusts itself automatically to the

depth setting and prevents chips and sawdust from

flying out towards you. Even at the minimum depth cut

setting the blade is covered, thus minimizing the risk

of accidents.

7 Putting into Operation

8 Replacing the Saw Blade

9 Swing guard

10 Eye shield

1500 KS.book Seite 10 Montag, 15. April 2002 11:11 11

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kress 1500 KS Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info