Bedienungsanleitung Kress KG745 (Seite 14 von 156) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Schwedisch)

819062

Zoom out

Zoom in

Vorherige Seite

1/156

Nächste Seite

3. When transporting your mower in a vehicle,

secure and position it to prevent movement or

damage.

Transporting the battery

1. Ensure the battery is in a safe condition.

2. Use non-conductive packaging when

transporting the battery.

3. The contained Li-Ion batteries are subject to the

dangerous goods legislation requirements.

Transport batteries only when the battery

housing is undamaged. Pack up the batteries in

such a manner that cannot move around in the

packaging.

MAINTENANCE

WARNING! Stop the mower before

removing the grass bag.

NOTE: To ensure long and reliable service, perform

the following maintenance procedures regularly.

Check for obvious defects such as a loose,

dislodged or a damaged blade, loose ttings,

and worn or damaged components. Check that

the covers and guards are all undamaged and

are correctly attached to mower. Carry out any

necessary maintenance or repairs before operating

mower. If the mower should happen to fail despite

regular maintenance, please call our customer

helpline for advice.

BLADE SHARPENING

KEEP BLADE SHARP FOR BEST MOWER

PERFORMANCE.

WEAR PROPER EYE PROTECTION WHILE

REMOVING, SHARPENING, AND INSTALLING

BLADE.

Sharpening the blade twice during a mowing season

is usually sufcient under normal circumstances.

Sand causes the blade to dull quickly. If your lawn

has sandy soil, more frequent sharpening may be

required.

REPLACE BENT OR DAMAGED BLADE

IMMEDIATELY.

WHEN SHARPENING THE BLADE:

1. Make sure blade remains balanced.

2. Sharpen blade at the original cutting angle.

3. Sharpen cutting edges on both ends of blade,

removing equal amounts of material from both ends.

NOTE:

Be sure the mower is turned off.

2. Place the mower in stand up storage mode.

TO SHARPEN BLADE IN A VISE (SEE Fig. J)

J-1

J-2

J-3

1. Be sure the switch lever is released, the blade

has stopped before removing the blade.

2. Remove blade from mower. See instructions for

removing and attaching blade.

3. Secure blade J-1 in a vise J-2.

4. Wear safety glasses and be careful not to cut

yourself.

5. Carefully le the cutting edges of the blade with a

ne tooth le J-3 or sharpening stone.

6. Check balance of blade. See instructions for

blade balancing.

7. Replace blade on mower and tighten securely.

Refer to instructions below.

BLADE BALANCING (SEE Fig. K)

Check balance of blade by placing center hole in

blade K-1 over a nail or screwdriver shank K-2,

clamped horizontally in a vise K-3. If either end of

the blade rotates downward, le that end. Blade is

properly balanced when neither end drops.

K-1

K-2

K-3

BLADE MAINTENANCE (See Fig. L1, L2)

Renew your metal blade after 50 hours mowing

or 2 years, whichever is the sooner-regardless of

condition.

Follow these procedures to remove and replace the

blade. You will need garden gloves (not provided)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kress KG745 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info